XC6209/6212
Series
■GENERAL
DESCRIPTION
ETR0306-003
High Speed LDO Regulator, Low ESR Cap. Compatible, Output ON/OFF Control
The XC6209/XC6212 series are highly precise, low noise, positive voltage LDO regulators manufactured using CMOS
processes. The series achieves high ripple rejection and low dropout and consists of a voltage reference, an error amplifier, a
current limiter and a phase compensation circuit plus a driver transistor.
Output voltage is selectable in 50mV increments within a range of 0.9V ~ 6.0V. The series is also compatible with low ESR
ceramic capacitors which give added output stability. This stability can be maintained even during load fluctuations due to the
excellent transient response of the series. The current limiter's foldback circuit also operates as a short protect for the output
current limiter and the output pin. The CE function enables the output to be turned off, resulting in greatly reduced power
consumption.
■APPLICATIONS
●Mobile
phones, Cordless phones
●Wireless
communication equipment
●Portable
games
●Cameras,
Video recorders
●Portable
AV equipment
●Reference
voltage
●Battery
powered equipment
■
FEATURES
: 150mA
(300mA=XC6209E to H types)
Dropout Voltage
: 60mV @ 30mA
200mV @ 100mA
Minimum Operating Voltage
: 2.0~10.0V
Output Voltage Range
: 0.9V ~ 6.0V (50mV increment)
Highly Accurate
:
±2%
(V
OUT
>1.5V)
±30mV
(V
OUT≦
1.5V)
Low Power Consumption
: 25μA (TYP.)
Stand-by Current
: Less than 0.1μA (TYP.)
Highly Ripple Rejection
: 70dB (10kHz)
Operating Temperature Range : -40℃~ +85℃
Low ESR Capacitor
: Ceramic capacitor compatible
Process
: CMOS
Built-In Circuit
: Current Limit Circuit
Ultra Small Packages
: SOT-25
USP-6B (XC6209)
SOT-89-5 (XC6209)
Maximum Output Current
■TYPICAL
APPLICATION CIRCUIT
■TYPICAL
PERFORMANCE
CHARACTERISTICS
1/25
XC6209/6212
Series
■PIN
CONFIGURATION
[XC6209]
CE 6
VSS 5
NC 4
1 VIN
2 NC
3 VOUT
*The dissipation pad for the USP-6B
package should be solder-plated in
recommended mount pattern and metal
masking so as to enhance mounting
strength and heat release.
USP-6B
(BOTTOM VIEW)
[XC6212]
■PIN
ASSIGNMENT
PIN NUMBER
XC6209
SOT-89-5 USP-6B
4
1
2
5
3
6
1
5
2,4
3
XC6212
SOT-25
3
2
4
5
1
PIN NAME
V
IN
V
SS
CE
NC
V
OUT
FUNCTION
Input
Ground
ON/OFF Control
No Connection
Output
SOT-25
1
2
3
4
5
■FUNCTIONS
TYPE
A, B, E, F Series
C, D, G, H Series
H=High Level
L=Low Level
CE
H
L
H
L
OPERATIONAL STATE
ON
OFF
OFF
ON
2/25
XC6209/6212
Series
■PRODUCT
CLASSIFICATION
●Selection
Guide
The following options for the CE pin logic and internal pull-up/down are available:
High Active + no pull-down resistor built-in (standard)
High Active+ 2MΩ pull-down resistor built-in <between CE-V
SS
> (semi-custom)
Low Active + no pull-up resistor built-in (semi-custom)
Low Active + 2MΩ pull-up resistor built-in <between V
IN
-CE> (semi-custom)
Note: *With the pull-up resistor or pull-down resistor built-in types, the supply current during operation will increase by
V
IN
/ 2MΩ (TYP.).
●Ordering
Information
XC6209/12①②③④⑤⑥
DESIGNATOR
①
(*1)
DESCRIPTION
Type of Regulator
CE Pin Logic
SYMBOL
A/E
B/F
C/G
D/H
②
③
Output Voltage
09~60
2
1
A
B
M
⑤
Packages
P
D
⑥
Device Orientation
R
L
DESCRIPTION
: High Active (pull-down resistor built-in, semi-custom)
: High Active (no pull-down resistor built-in, standard)
: Low Active (pull-up resistor built-in, semi-custom)
: Low Active (no pull-up resistor built-in, standard)
: e.g. 20:2.0V,
30:3.0V,
: 100mV increments,
±2%
accuracy (*2)
e.g.
②=2, ③=8, ④=2 →
2.80V,
±2%
: 100mV increments,
±1%
accuracy (*2)
e.g.
②=2, ③=8, ④=1 →
2.80V,
±1%
: 50mV increments,
±2%
accuracy (*2)
e.g.
②=2, ③=8, ④=A →
2.85V,
±2%
: 50mV increments,
±1%
accuracy (*2)
e.g.
②=2, ③=8, ④=B →
2.85V,
±1%
: SOT-25 (SOT-23-5)
: SOT-89-5 (for XC6209 series only)
: USP-6B (for XC6209 series only)
: Embossed tape, standard feed
: Embossed tape, reverse feed
④
Output Voltage
Accuracy
(*1) Maximum output current of E to H series depend on the setting voltage.
(*2) Within
±30mV
(V
OUT
≦
1.5V)
3/25
XC6209/6212
Series
■BLOCK
DIAGRAM
■ABSOLUTE
MAXIMUM RATINGS
Ta=25℃
PARAMETER
Input Voltage
Output Current
Output Voltage
CE Input Voltage
SOT-25
SOT-89-5
Power Dissipation
USP-6B
Operating Temperature Range
Storage Temperature Range
Topr
Tstg
SYMBOL
V
IN
I
OUT
V
OUT
V
CE
Pd
RATINGS
12.0
500 *
V
SS
- 0.3 ~ V
IN
+ 0.3
V
SS
- 0.3 ~ V
IN
+ 0.3
250
500
100
-40 ~ +85
-55 ~ +125
℃
℃
UNITS
Ｖ
mA
Ｖ
Ｖ
mW
*NOTE: Within the range of I
OUT
=Pd / (V
IN
– V
OUT
)
4/25
XC6209/6212
Series
■ELECTRICAL
CHARACTERISTICS
XC6209/6212A, B Series
PARAMETER
Output Voltage
Maximum Output Current
Load Regulation
Dropout Voltage (*4)
Supply Current (A series)
I
DD
Supply Current (B series)
Standby Current
Istby
△V
OUT
△V
IN
½V
OUT
V
IN
△V
OUT
△Topr½V
OUT
PSRR
I
lim
Ishort
V
CEH
V
CEL
I
CEH
I
CEH
I
CEL
V
IN
=V
CE
=V
OUT(T)+
1.0V
(V
OUT
<0.95V)=(V
IN
=V
CE
=2.0V)
V
IN
=V
CE
=V
OUT(T)+
1.0V
(V
OUT
<0.95V)=(V
IN
=V
CE
=2.0V)
V
IN
=
VOUT(T)+
1.0V, V
CE
=V
SS
(V
OUT<
0.95V)=(V
IN
=2.0V)
If V
OUT
is less than 0.95V, V
IN
= 2.0V.
Ta=25℃
SYMBOL
V
OUT(E)
I
OUTMAX
△V
OUT
Vdif1
Vdif2
CONDITIONS
2% accuracy (*7)
I
OUT
=30mA
1% accuracy (*8)
1mA< I
OUT
<100mA
I
OUT
=30mA
I
OUT
=100mA
V
IN
=V
CE
= V
OUT(T)+
1.0V
(V
OUT
<0.95V)=(V
IN
=V
CE
=2.0V)
V
IN
=V
CE
=V
OUT(T)+
1.0V
(V
OUT
<0.95V)=(V
IN
=V
CE
=2.0V)
V
IN
=V
OUT(T)+
1.0V, V
CE
=V
SS
(V
OUT
<0.95V)=(V
IN
=2.0V)
V
OUT(T)+
1.0V<V
IN
<10V
(V
OUT
<0.95V)=(2.0V<V
IN
<10V)
I
OUT
=30mA
(V
OUT
<1.75V)=(I
OUT
=10mA)
I
OUT
=30mA
-40℃<Topr<85℃
V
IN
={V
OUT(T)+
1.0}V+1.0Vp-pAC,
(V
OUT
<1.5V)=(V
IN
=2.5V+1.
0Vp-pAC
)
, I
OUT
=50mA, f=10kHz
V
IN
=V
OUT(T)+
1.0V, V
CE
=V
IN
,
(
V
OUT<
1.75V
)=(
V
IN=
V
OUT(T)+
2.0V
)
V
IN
=V
OUT(T)+
1.0V, V
CE
=V
IN
,
(
V
OUT<
1.75V
)=(
V
IN=
V
OUT(T)+
2.0V
)
MIN.
×0.98
×0.99
150
-
TYP.
V
OUT(T)
V
OUT(T)
-
15
E-1
E-2
28
25
-
0.01
MAX.
×1.02
×1.01
-
50
UNITS CIRCUIT
V
mA
mV
mV
1
1
1
1
-
55
μA
50
0.10
μA
2
2
Line Regulation
Input Voltage
Output Voltage
Temperature Characteristics
Ripple Rejection Rate
Current Limiter
Short-circuit Current
CE "High" Level Voltage
CE "Low" Level Voltage
CE "High" Level Current
(A series)
CE "High" Level Current
(B series)
CE "Low" Level Current
NOTE :
-
2
-
-
-
-
1.6
-
0.60
-0.10
-0.10
0.01
-
100
70
300
50
-
-
-
0.20
10
-
-
-
-
V
IN
0.25
5.0
0.10
％/V
V
ppm
/℃
dB
mA
mA
V
V
μA
1
-
1
4
1
1
1
2
2
-
0.10
μA
2
* 1: Unless otherwise stated, V
IN
=V
OUT(T)+
1.0V.
* 2: V
OUT(T)=
Specified output voltage
* 3: V
OUT(E)=
Effective output voltage
(I.e. the output voltage when "V
OUT(T)+
1.0V" is provided at the V
IN
pin while maintaining a certain I
OUT
value).
* 4: Vdif={V
IN1
(*6)
-V
OUT1
(*5)
}
* 5: V
OUT1
=A voltage equal to 98% of the output voltage whenever an amply stabilized I
OUT
{V
OUT(T)+
1.0V} is input.
* 6: V
IN1
=The input voltage when V
OUT1
appears as Input Voltage is gradually decreased.
* 7: If V
OUT(T)
is less than 1.45V, V
OUT(T)
-30mV (MIN.),
V
OUT(T)
+ 30mV (MAX.)
* 8: Only for the V
OUT(T)
more than 3.0V products.
5/25
京公网安备 11010802033920号
EEWORLD
