P-SKFL31 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > unclassified> P-SKFL31

Preview

P-SKFL31: DescriptionPETROLEUM SORBENT SPILL KIT P-SK; Categoryunclassified; File Size188KB，4 Pages; Manufacturer3M; Websitehttp://3M.com/esd

Download Datasheet View All

P-SKFL31 Overview

PETROLEUM SORBENT SPILL KIT P-SK

Preview

Download Datasheet

View All

March 2015

Technical Data

3M™ Chemical Sorbents

Use

For control of spills of certain hazardous liquids.

Product Description

3M™ Chemical Sorbents are made from inert, synthetic fibers principally polypropylene and polyester. They are available in

a wide range of formats and are lightweight and nominally dust-free. They have a high adsorption capacity which minimizes

the amount of waste for disposal.

Color

Highly visible. Yellow (High Capacity pads and rolls, P-110 pads), yellow with multi-colored material flecks (Medium Capacity

pads and rolls). Mini-booms and pillows are white with black print. Medium Capacity appearance may vary due to recycle

content used.

Selection Guide



Folded – Combines four formats in one product. It is perforated every 16 inches (40 cm) and can be unfolded to be used



as booms, pillows, sheets or rolls.

Minibooms – Generally on-land applications to contain and adsorb spills.

Pillows – Used for bulk absorption of oil on land or water. Particularly useful in drains to act as interceptors.

Pads – A highly adaptable format. They can be used on water to pick up oil covering large surface areas and in wiping

applications.

Particulate – For fast coverage and adsorption of spills.

Rolls – For fast coverage of large surface areas of water, they can be easily torn to length. Also used as a mat to keep

shorelines or banks clean and to place used sorbents upon.

Spill Kits and Response Packs – May contain different types of sorbents and temporary disposal bags. Compact for easy

storage and quick response.

Typical Liquids Adsorbed

3M chemicals sorbents are suitable for adsorbing a wide range of liquids including certain acids, bases, coolants, petroleum

based fluids, non-aggressive chemicals and aqueous based solutions.

March 2015

Limitations of Use

3M recommends that a compatibility test with the liquid of interest be carried out prior to using the sorbent. For use in

temperature over 60C it is essential that such a compatibility test is made prior to use. Do not use 3M chemical sorbents with

the following concentrated chemicals as there is a risk of degradation: oleum, chlorosulfonic acid, liquid bromine, fuming nitric

acid, chromic acid, sulfuric acid and hydrogen peroxide.

Precautions

3M chemical sorbents are not in themselves hazardous products, however, they take on the characteristics of the liquids they

adsorb. Adequate precautions should be taken when handling or storing hazardous / flammable materials and appropriate

personal protective equipment should be worn. Users should be informed of the risks incurred in use, storage and disposal

of used sorbents.

Disposal

Dispose of used sorbents only in accordance with local and national regulations. Disposal companies should be consulted

for their recommendations.

Waste Minimization

3M recommends that waste streams should be minimized wherever possible. 3M sorbents promote minimization by only

being a small part of the total waste. In addition where laws allow, 3M sorbents can be disposed of by incineration yielding

less than 0.2% ash (ASTM D-482). The high energy value of the sorbents is also favorable for incineration and waste-to-fuel

systems.

Sustainability

High Capacity sorbents contain at least 25% recycled content by weight. Medium Capacity sorbents contain at least 50%

recycled content by weight.

Adsorption / Sorbency

The sorbent capacity quoted in the table below is based on testing per ASTM F 726 “Standard Test Method for Sorbent

Performance of Adsorbents.” In brief, the sorbent samples were immersed in a “medium” density oil, drained and weighed.

In the 1981 version of the standard, samples are immersed for a variable period of time in an attempt to make sure the

sorbent is saturated. The sorbent is then drained horizontally. In the 2006 version of the standard, samples are immersed

for 15 minutes and then most types are drained vertically. Capacity according to both versions of the standard is presented.

Data presented are nominal; there will be variability in sorbent performance.

Capacity and speed of adsorption will

differ depending on the liquid’s polarity, surface tension and viscosity. Ambient temperature may also affect results.

Therefore, results will vary by application.

Recommended Resources

Ultrasonic remote control delay light switch circuit

MAX630 minimum structure DC-DC conversion circuit diagram

Crystal Controlled Super Regenerative Receiver

camera flash circuit

10x voltage rectifier circuit

Frequent commutation circuit of capacitor-started single-phase motor

Behavioral modeling sequential logic circuit (two-input AND gate) source code and test code: Source code:module and_gate1(clk, a, b, s);input clk;input a;input b;output reg s;//Behavioral modeling sequential logic circuit (two-input AND gate)always @ (posedge clk) //Rising edge triggeredbegin...; zxopenljx FPGA/CPLD

Hardware testing method for TI-CC chip: Brief description Forced to do something that is meaningless to the current direction, we can only grab some meaning from it.Based on TI's test software smartRF studio, the hardware needs to reserve V...; 火辣西米秀 Wireless Connectivity

Is the digital-to-analog configuration of a certain pin of STM32 related to the output? Do I need to set the output register of this pin when outputting?: Is the digital-to-analog configuration of a certain pin of STM32 related to the output? Do I need to set the output register of this pin when outputting?...; 深圳小花 stm32/stm8

EEWORLD University ---- Microprocessor and Embedded System Design University of Electronic Science and Technology of China: Microprocessor and Embedded System Design University of Electronic Science and Technology of China : https://training.eeworld.com.cn/course/5402...; 木犯001号 MCU

MSP430G2553 Study Notes: MSP430G2553 OverviewLow supply voltage range: 1.8V to 3.6VUltra-low power– Run mode: 230μA (at 1MHz and 2.2V)– Standby mode: 0.5μA– Off mode (RAM retention): 0.1μ5 power-saving modesUltra-fast wake-up...; Aguilera Microcontroller MCU

[Silicon Labs BG22-EK4108A Bluetooth Development Review] Unboxing: [ Silicon Labs BG22-EK4108A Bluetooth Development Review] UnboxingOn January 2 , 2022, I received the development board BG22-EK4108A from Silicon Labs and Arrow Electronics . I would like to thank the...; ly87802541 Development Kits Review Area

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components