No load condition, f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
No load condition, f = 20 MHz, Vdd = 1.8V
Vdd = 2.5V, 2.8V, 3.3V, ST = GND, output is Weakly Pulled Down
Vdd = 1.8V, ST = GND, output is Weakly Pulled Down
See the Absolute Pull Range and APR table on
page 10
Vdd = 1.8V, Voltage at which maximum deviation is guaranteed.
Vdd = 2.5V, Voltage at which maximum deviation is guaranteed.
Vdd = 2.8V, Voltage at which maximum deviation is guaranteed.
Vdd = 3.3V, Voltage at which maximum deviation is guaranteed.
Voltage at which minimum deviation is guaranteed.
Additional supply voltages between 2.5V and 3.3V can be
supported. Contact
SiTime
for additional information.
Condition
Refer to
Table 11
for the exact list of supported frequencies
Inclusive of Initial tolerance
[4]
at 25 °C, and variation over
temperature, rated supply voltage and load.
10 years, 25°C
Extended Commercial
Industrial
Frequency Range
Frequency Stability and Aging
Supply Voltage and Current Consumption
VCXO Characteristics
±25, ±50, ±100, ±150, ±200
1.7
2.4
2.7
3.2
Lower Control Voltage
Control Voltage Input Impedance
Control Voltage Input Capacitance
Linearity
Frequency Change Polarity
Control Voltage Bandwidth (-3dB)
Duty Cycle
Rise/Fall Time
Output High Voltage
VC_L
Z_in
C_in
Lin
–
V_BW
DC
Tr, Tf
VOH
–
45
–
90%
–
100
–
–
–
–
–
–
–
–
5
0.1
Positive slope
8
–
1.5
–
–
–
–
–
0.1
–
–
1
Upper Control Voltage
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
SiTime Corporation
Rev. 1.01
990 Almanor Avenue, Sunnyvale, CA 94085
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Table 1. Electrical Characteristics
[1, 2, 3]
Parameter
Input Pull-up Impedance
Input Capacitance
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Jitter
RMS Phase Jitter (random)
Symbol
Z_in
C_in
T_start
T_oe
T_resume
T_jitt
T_phj
Electrical Specifications
(continued)
Min.
–
–
–
–
–
–
–
–
Typ.
100
5
–
–
7
1.5
2
0.5
Max.
250
–
10
180
10
Jitter
2
3
1
ps
ps
ps
f = 20 MHz, Vdd = 2.5V, 2.8V or 3.3V
f = 20 MHz, Vdd = 1.8V
f = 20 MHz, Integration bandwidth = 12 kHz to 20 MHz, All Vdds
Unit
kΩ
PF
ms
ns
ms
Condition
For the OE/ST pin for 6-pin devices
For the OE/ST pin for 6-pin devices
See Figure 7 for startup resume timing diagram
f = 40 MHz, all Vdds. For other freq, T_oe = 100 ns + 3 clock
periods
See Figure 8 for resume timing diagram
Input Characteristics
Startup and Resume Timing
Notes:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
2. The typical value of any parameter in the Electrical Characteristics table is specified for the nominal value of the highest voltage option for that parameter and at
25 °C temperature.
3. All max and min specifications are guaranteed across rated voltage variations and operating temperature ranges, unless specified otherwise
4. Initial tolerance is measured at Vin = Vdd/2
5. Absolute Pull Range (APR) is defined as the guaranteed pull range over temperature and voltage.
6. APR = pull range (PR) - frequency stability (F_stab) - Aging (F_aging)
Rev. 1.01
Page 2 of 11
www.sitime.com
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Table 2. Pin Description. 4-Pin Configuration
(For 2.5 x 2.0 mm and 3.2 x 2.5 mm packages)
Pin
1
2
3
4
Symbol
VIN
GND
CLK
VDD
Input
Power
Power
Input
Power
Electrical ground
Power supply voltage
Oscillator output power
[7]
GND
2
3
Top View
Functionality
VIN
1
4
0-Vdd: produces voltage dependent frequency change
VDD
CLK
Note:
7. A capacitor value of 0.1 µF between VDD and GND is recommended.
Figure 1.
Table 3. Pin Description. 6-Pin Configuration
(For 5.0 x 3.2 mm and 7.0 x 5.0 mm packages)
Pin
1
Symbol
VIN
Input
No
Connect
2
NC/OE/ ST
Output
Enable
Standby
3
4
5
6
GND
CLK
NC
VDD
Power
Output
No
Connect
Power
Functionality
0-Vdd: produces voltage dependent frequency change
H or L or Open: No effect on output frequency or other device
functions
H or Open
[8]
: specified frequency output
L: output is high
H or Open
[8]
: specified frequency output
L: output is low (weak pull down)
[9]
. Oscillation stops
Electrical ground
Oscillator output
H or L or Open: No effect on output frequency or other device
functions
Power supply
voltage
[10]
VIN
NC/OE/ST
GND
1
6
Top View
VDD
NC
CLK
2
5
3
4
Figure 2.
Notes:
8. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 2 in the 6-pin package is not externally driven. If pin 2 needs to be left floating, use
the NC option
9. Typical value of the weak pull-down impedance is 5 mΩ
10. A capacitor value of 0.1 µF between VDD and GND is recommended.
Table 4. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance of
the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Min.
-65
-0.5
–
–
Max.
150
4
2000
260
Unit
°C
V
V
°C
Table 5. Thermal Consideration
Parameter
7050
5032
3225
2520
JA, 4 Layer Board
(°C/W)
191
97
109
117
JA, 2 Layer Board
(°C/W)
263
199
212
222
JC, Bottom
(°C/W)
30
24
27
26
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Rev. 1.01
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Page 3 of 11
www.sitime.com
SiT3807
Standard Frequency MEMS VCXO
The Smart Timing Choice
The Smart Timing Choice
Phase Noise Plot
-100
-110
-120
-130
-140
-150
-160
-170
3
10
Integrated random phase jitter (RMS, 12kHz-5MHz): 0.52ps
Crown, Reiz, leaking! Leaking oil! LS GS300, keep up, keep up, Toyota has done a great job, Toyota is leaking a lot! Don't give other cars any chance! Oil leakage belongs to Toyota! The great Toyota...
1. Choose UPS according to the power and power factor of the equipment. After you purchase the equipment, you can use the following conservative method to calculate the load power. (1) For single-phas...
There is no one to teach me how to learn FPGA. Can I learn it just by watching tutorials? I have bought a black gold FPGA development board. The only information I can find is the source code provided...
[b]Which friend[/b] has used [b][u]domestic[/u] driver chips for [b]brushless DC motors and [b] brushless DC motors? Requirements: [/b]Continuous output current above 3A, peak current above 6A, operat...
Python has been very popular in the past two years. Big data, artificial intelligence, and deep learning all use Python. When I was in college, I also taught myself how to do it, but I didn't expect i...
HDYZ-E zinc oxide lightning arrester live tester panel and components function introduction 1 Hosting Panel The layout of the host panel is shown in Figure 3. 1.1 Current input: There are three inpu...[Details]
Dialog Semiconductor, a leading supplier of highly integrated power management, AC/DC power conversion, charging and Bluetooth low energy technologies, has announced that Samsung has adopted Dialog’s...[Details]
AVI file format diagram
tidy:
AVI is a container that can hold data in any format.
Video encoding: The format can be H264, MPEG-4, MJPEG. Since MJPEG is relatively simple, ...[Details]
The Shanghai Stock Exchange has officially accepted the application of Wuxi Shengjing Microelectronics Co., Ltd. (hereinafter referred to as Shengjing Micro) for listing on the Science and Technology...[Details]
After the production capacity ramp-up, iQOO adjusted its mobile phone sales strategy: at 10 a.m. every day, iQOO will be available for sale in limited quantities across the entire network. With the e...[Details]
0 Introduction
LED lighting is the mainstream of energy saving in the world, and high-power LED lighting is the mainstream trend of lighting systems in the future. High-power LED has the chara...[Details]
Recently, the internationally renowned financial magazine Barron's released the 2018 list of the world's best CEOs. 30 outstanding company leaders were listed for their courage to meet challenges and...[Details]
DIP can also be an English abbreviation. It has multiple meanings: DIP package, desquamative interstitial pneumonia, one of the software design principles, protein interaction database, defect interfe...[Details]
Recently, due to insufficient production capacity of KrF (248nm) photoresist produced by Japan's Shin-Etsu Chemical, many Chinese wafer fabs are facing tight supply of KrF photoresist, and some small...[Details]
The inverter has many setting parameters, and each parameter has a certain selection range. In use, it is often encountered that the inverter cannot work normally due to improper setting of individ...[Details]
1 Introduction
Many people believe that with the popularity of computers, information can be stored in electronic media, thus reducing the amount of paper used. However, due to the conve...[Details]
In recent years, due to economic development, the use of electronic truck scales has been expanding. Because of its automatic display, automatic recording, elimination of human interference, fast and...[Details]
Systick, also known as tick timer, is a 24-bit simple timer of the STM32 core, often used for delay and system heartbeat functions. Systick has a total of 4 registers CTRL, LOAD, VAL, CALIB The def...[Details]
/*--------------------------------------------------------------------------
ST7920.H
The user function is C51.
Copyright (c) 1988-2004 Keil Elektronik GmbH sum zhaojun
All rights reserved.
----...[Details]
The control requirements of servo drives for servo motors is a complex and in-depth topic. The following is an overview of the control requirements of servo drives for servo motors:
Preci...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
