Commercial Device Servers
Compact size enables it to fit almost anywhere
Supports RS-232, RS-422 and RS-485 serial connections
10Mbps or 10/100 Mbps Ethernet through an RJ45 connector
Configure via HTTP, DHCP, Telnet or serial
Flash ROM for easy upgrades
Remotely Monitor, Manage and Share Devices
Over a Network or the Internet
In today’s economy, faster and better access to
information can mean the difference between success
and failure. The UDS-10 and UDS100 single-port device
servers provide a quick, simple and cost-effective way to
bring the advantages of data accessibility and remote
management to equipment not currently connected
to a network.
Our approach to network-enabling devices is
transparent to your attached devices and software.
So, you won’t need to change the way you work,
and there’s no need to develop special software to
take advantage of Ethernet networking. And with the
UDS-10(10Base-T) and UDS100(100Base-T/100Base-TX)
any piece of equipment with a serial port can be
added to the network in a matter of minutes!
Using a method called serial tunneling, UDS
encapsulates serial data into packets and transports it
over Ethernet. Using two UDS Device Servers
™
connected by a network, virtual serial connections can
be extended across a facility or around the world. So
you can manage your equipment from virtually
anywhere over Ethernet or the Internet.
The included redirection software extends the
functionality of your COM port-based Windows
®
applications. With virtual COM ports, mapped to
remote device servers on the network, you can replace
direct serial connections.
Easy to Set Up and Use
The included Windows-based configuration software
simplifies installation and setup. The UDS-10 and
UDS100 can also be set up locally through the serial
port, or remotely over a network using Telnet or a
web browser.
The UDS even includes a built-in web server, which can
be used for configuration, or to display operating and
troubleshooting information on the attached links to
online support.
Flash memory provides for maintenance-free non-
volatile storage of web pages, and allows future
system software upgrades.
Modem Replacement
In modem emulation mode, the UDS-10 and UDS100
can be used to replace dial-up modems. The unit
accepts modem AT commands on the serial port, then
establishes a network connection to the end device,
leveraging network connections and bandwidth to
eliminate dedicated modems and phone lines.
If you’re looking for a transparent, cost-effective, and
scalable means to network-enable your serial devices,
look no further than the UDS-10 and UDS100.
Device Server
™
UDS-10/UDS100
Replace expensive dedicated PCs with fast and reliable
networking technology
UDS-10/UDS100
Example Configurations
Features
Protocols Supported
ARP, UDP, TCP, Telnet, ICMP, SNMP, DHCP, TFTP, and HTTP
Device Support
Supports any asynchronous serial device with 7 or 8-bit
data,with or without parity requiring Ethernet access
Network Interface
RJ45
(10Base-T)
Ethernet (UDS-10)
RJ45
(10Base-T/100Base-TX)
Ethernet (UDS
100)
Serial Interface
DB25F, RS-232/RS-422/RS-485 serial port
with DCE configuration
Data Rates
Serial speeds 300 bps to 115 Kbps
Modem Controls
RTS, CTS, DSR, DCD, DTR
Flow Control
Software XON/XOFF
Hardware CTS/RTS
Management
Internal HTTP server
SNMP
(read only)
Serial login
Telnet login
Firmware
Flash ROM standard; downloadable from a TCP/IP host
(TFTP)
or over the serial port
Indicators (LED)
Good Link
(green)
Network transmit/Receive data
(yellow)
Collisions
(red)
Diagnostic
(red)
Status
(green)
Power
Power input via standard barrel connector or
DB25 serial connector
Input Range: 9 to 30 VDC or 9 to 24 VAC @ 1W max
Environmental
Operating: 5° to 50° C
(41° to 122° F)
Storage: -40° to 66° C
(-40° to 151° F)
Physical
Dimensions: 9.0 x 6.4 x 2.3 cm
(3.5 x 2.5 x 0.9 in)
Weight: .35 Kg
(.8 lb)
Shipping Dimensions: 24.2 x 19.1 x 11.5 cm
(9.5 x 7.5 x 4.5 in),
Weight: 1.5 kg
(3.0 lb)
Agency Approvals
CE, FCC B, TUV, C/UL
Warranty
1-year limited warranty
SERIAL TUNNELING CONFIGURATION
Ethernet
UDS
Device Servers
Device Server
™
POS Device
Personal Computer (PC)
DIRECT TCP/IP
OR REDIRECTOR CONFIGURATION
Ethernet
UDS
Device Server
Personal Computer (PC)
POS Device
Ordering Information
UDS-10-01
Device Server, 1 DB25 (RS-232/RS-485/
RS-422) DCE serial port, RJ45 (10Base-T)
network ports, diagnostic LEDs, installation
guide, external 110 VAC power supply
UDS-10-02
Same as above with 100-240 VAC power
supply with international adapters
UDS-M-SBC
Optional male DB25 to screw terminal block connector
UDS-100-01
Device Server, 1 DB25 (RS-232, RS-422, RS-485)
DCE serial port, RJ45 (10Base-T/100Base-TX)
network ports, diagnostic LEDs, installation
guide, external 110 VAC power supply
UDS-100-02
Same as above with 100-240 VAC power supply
with international adapters
15353 Barranca Parkway
|
Irvine
|
CA 92618
|
USA
|
Tel: 800.422.7055
|
Fax: 949.450.7232
|
www.lantronix.com
©2006 Lantronix, Inc. Lantronix is a registered trademark, and Device Server is a trademark of Lantronix, Inc. All other trademarks are the property of their respective owners. Specifications subject to
change without notice. All rights reserved.
910-316 07/06 DGS2500
Security Electronics
京公网安备 11010802033920号
EEWORLD
