LM193W - LM293W
LM393W
LOW POWER DUAL VOLTAGE COMPARATORS
s
WIDE SINGLE SUPPLY VOLTAGE RANGE
s
s
s
s
s
s
s
s
s
OR DUAL SUPPLIES : +2V TO +36V OR ±1V
TO ±18V
VERY LOW SUPPLY CURRENT (0.4mA)
INDEPENDENT OF SUPPLY VOLTAGE
(1mW/comparator at +5V)
LOW INPUT BIAS CURRENT : 25nA TYP
LOW INPUT OFFSET CURRENT : ±5nA TYP
LOW INPUT OFFSET VOLTAGE : ±1mV TYP
INPUT COMMON-MODE VOLTAGE RANGE
INCLUDES GROUND
LOW OUTPUT SATURATION VOLTAGE :
250mV TYP. (Io = 4mA)
DIFFERENTIAL INPUT VOLTAGE RANGE
EQUAL TO THE SUPPLY VOLTAGE
TTL, DTL, ECL, MOS, CMOS COMPATIBLE
OUTPUTS
ESD INTERNAL PROTECTION: 2kV
N
DIP8
(Plastic Package)
D
SO8
(Plastic Micropackage)
DESCRIPTION
These devices consist of two independent low
voltage comparators designed specifically to oper-
ate from a single supply over a wide range of volt-
ages. Operation from split power supplies is also
possible.
These comparators also have a unique character-
istic in that the input common-mode voltage range
includes ground even though operated from a sin-
gle power supply voltage.
All the pins are protected against electrostatic dis-
charge up to 2kV. As a consequence, the input
voltages must not exceed the magnitude of Vcc+
or Vcc-.
PIN CONNECTIONS
(top view)
P
TSSOP8
(Thin Shrink Small Outline Package)
ORDER CODE
Part
Number
Temperature
Range
Package
N
D
P
LM193W
-55°C, +125°C
LM293W
-40°C, +105°C
LM393W
0°C, +70°C
Example :
LM393WD
•
•
•
•
•
•
•
•
•
N =
Dual in Line Package (DIP)
D =
Small Outline Package (SO) - also available in Tape & Reel (DT)
P =
Thin Shrink Small Outline Package (TSSOP) - only available in Tape
&Reel (PT)
1
2
3
4
5
6
7
8
- Output 1
- Inverting input 1
- Non-inverting input 1
- V
CC-
- Non-inverting input 2
- Inverting input 2
- Output 2
- V
CC+
May 2004
1/10
LM193W - LM293W - LM393W
SCHEMATIC DIAGRAM
(1/2 LM193)
VCC+
3.5µA
100µA
3.5µA
100µA
VCC+
VCC+
Non-Inverting
Input
Vo
VCC-
Inverting
Input
VCC-
VCC-
VCC-
VCC-
ABSOLUTE MAXIMUM RATINGS
Symbol
V
CC
V
id
V
i
P
tot
T
oper
T
stg
1.
Parameter
Supply voltage
Differential Input Voltage
Input Voltage
Output Short-circuit to Ground - note
1)
Power Dissipation
Opearting Free-air Temperature Range
Storage Temperature Range
LM193W
LM293W
±18 or 36
LM393W
Unit
V
V
V
mW
V
CC-
-0.3 to V
CC+
+0.3
Infinite
830
-55 to +125 -40 to +105
-65 to +150
0 to +70
°C
°C
Short-circuits from the output to V
CC +
can cause excessive heating and eventual destruction. The maximum output current is approximately 20mA
independent of the magnitude of V
CC +
.
2/10
LM193W - LM293W - LM393W
ELECTRICAL CHARACTERISTICS
V
CC
+
= +5V, V
CC
-
= 0V, T
amb
= +25°C (unless otherwise specified)
Symbol
V
io
Parameter
Input Offset Voltage - note
1)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Input Bias Current - note
2)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Input Offset Current
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Large Signal Voltage Gain
V
CC
= 15V, R
L
= 15k
Ω,
V
o
= 1V to 11V
Supply Current (all comparators)
V
CC
= 5V, no load
V
CC
= 30V, no load
Input Common Mode Voltage Range - note
3)
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Differential Input Voltage -note
4)
Output Sink Currrent
V
id
= 1V, V
o
= 1.5V
Low Level Output Voltage
V
id
= -1V, I
sink
= 4mA
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
High Level Output Current (V
id
= 1V)
I
OH
V
id
= 1V, V
CC
= V
o
= 30V
T
amb
= +25°C
T
min
≤
T
amb
≤
T
max
Response Time - note
5)
R
L
= 5.1k
Ω
to V
CC+
Large Signal Response Time
V
i
= TTL, V
(ref)
= +1.4V, R
L
= 5.1k
Ω
to V
CC+
0.1
1
nA
µ
A
6
16
0
0
50
Min
Typ.
1
Max.
5
9
250
400
50
150
Unit
mV
I
ib
25
nA
I
io
5
nA
A
vd
200
0.4
1
1
2.5
V
CC+
-1.5
V
CC
-2
V
CC+
+
V/mV
mA
I
CC
V
icm
V
id
Isink
V
V
mA
V
OL
250
400
700
mV
t
re
t
rel
1.
2.
3.
4.
5.
1.3
300
µ
s
ns
At output switch point, V
o
≈
1.4V, R
s
= 0 with V
CC +
from 5V to 30V, and over the full common-mode range (0V to V
CC +
-1.5V).
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the
output, so no loading charge exists on the reference of input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the
common-mode voltage range is V
CC +
-1.5V, but either or both inputs can go to +30V without damage
Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than -0.3V (or 0.3V bellow the negative power supply, if
used).
The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be obtained
3/10
LM193W - LM293W - LM393W
4/10
LM193W - LM293W - LM393W
5/10
京公网安备 11010802033920号
EEWORLD
