EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

LMV1012XP-15/NOPB

Description
Microphone Preamplifiers Analog Pre-Amplified IC for High Gain Microphones 4-DSBGA
CategoryAnalog mixed-signal IC    Consumption circuit   
File Size1MB,23 Pages
ManufacturerTexas Instruments
Websitehttp://www.ti.com.cn/
Environmental Compliance
Stay tuned Parametric

LMV1012XP-15/NOPB Overview

Microphone Preamplifiers Analog Pre-Amplified IC for High Gain Microphones 4-DSBGA

LMV1012XP-15/NOPB Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Parts packaging codeDSBGA
package instructionVFBGA, BGA4,2X2,20
Contacts4
Reach Compliance Codecompliant
ECCN codeEAR99
Factory Lead Time1 week
Is SamacsysN
Nominal bandwidth95000 kHz
Commercial integrated circuit typesAUDIO PREAMPLIFIER
Gain15.6 dB
harmonic distortion0.09%
JESD-30 codeR-PBGA-B4
JESD-609 codee1
length1.031 mm
Humidity sensitivity level1
Number of channels1
Number of functions1
Number of terminals4
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package body materialPLASTIC/EPOXY
encapsulated codeVFBGA
Encapsulate equivalent codeBGA4,2X2,20
Package shapeRECTANGULAR
Package formGRID ARRAY, VERY THIN PROFILE, FINE PITCH
Peak Reflow Temperature (Celsius)260
power supply2.2/5 V
Certification statusNot Qualified
Maximum seat height0.3 mm
Maximum slew rate0.325 mA
Maximum supply voltage (Vsup)5 V
Minimum supply voltage (Vsup)2 V
surface mountYES
Temperature levelINDUSTRIAL
Terminal surfaceTin/Silver/Copper (Sn/Ag/Cu)
Terminal formBALL
Terminal pitch0.5 mm
Terminal locationBOTTOM
Maximum time at peak reflow temperatureNOT SPECIFIED
width0.955 mm
Base Number Matches1
Output swings to GND Single supply, low side, unidirectional current circuit
Please help explain the title, and if possible, write a waveform explanation by hand, thank you!...
zzw_rst Analog electronics
About the problem of converting schematic diagram to PCB when designing RF PCB circuit
I am using Altium Designer to design a Ku-band PCB. The chip package size is relatively small, and the spacing between pads is also small. If I import the schematic directly into the PCB, I will find ...
明天你好123 PCB Design
QSPI read, write and erase flash
I originally wanted to test the low power consumption, but when I saw that the board had to be cut, I decided to leave it for later and run the external flash function first. 1. Determine the hardware...
过问_小白 GD32 MCU
NEC begins testing flying cars
On the 5th of this month, Japan's NEC began testing unmanned flying cars. The flying car tested this time is about 4 meters long and weighs 150 kilograms. It uses electric motors to rotate four propel...
ellian1104 Automotive Electronics
The function and usage of the segmented storage function of the digital oscilloscope
To understand the segmented memory function of the oscilloscope, let us first look at what problems this function solves and what its value is. First of all, we must make it clear that the digital osc...
Micsig麦科信 Test/Measurement
Switching power supply problem
I spent 40 yuan to buy a 5V/12V dual output switching power supply. 5V and 12V are independent of each other.I used it once a few days ago, and today I needed to use the 5V power supply again. I teste...
chenbingjy Analog electronics

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号