To avoid sinking GND current from terminal Z when switch current flows in terminal Yn, the voltage drop across the bidirectional switch must not exceed
0.4 V. If the switch current flows into terminal Z, no GND current will flow from terminal Yn. In this case, there is no limit for the voltage drop across the
switch.
Applies to control signal levels.
10 Static characteristics
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
V
IH
HIGH-level
input voltage
Conditions
V
CC
= 1.65 V to 1.95 V
V
CC
= 2.3 V to 2.7 V
V
CC
= 3 V to 3.6 V
V
CC
= 4.5 V to 5.5 V
-40 °C to +85 °C
Min
0.65V
CC
1.7
2.0
0.7V
CC
-
-
-
-
[2]
-40 °C to +125 °C
Min
0.65V
CC
1.7
2.0
0.7V
CC
-
-
-
-
-
-
-
Unit
V
V
V
V
V
V
V
V
μA
μA
μA
μA
Typ
-
-
-
-
-
-
-
-
[1]
Max
-
-
-
-
0.35V
CC
0.7
0.8
0.3V
CC
±1
±0.2
±1
4
Max
-
-
-
-
0.35V
CC
0.7
0.8
0.3V
CC
±1
±0.5
±2
4
V
IL
LOW-level
input voltage
V
CC
= 1.65 V to 1.95 V
V
CC
= 2.3 V to 2.7 V
V
CC
= 3 V to 3.6 V
V
CC
= 4.5 V to 5.5 V
I
I
I
S(OFF)
I
S(ON)
I
CC
input leakage
current
OFF-state
leakage current
ON-state
leakage current
supply current
pin S; V
I
= 5.5 V or GND;
V
CC
= 0 V to 5.5 V
V
CC
= 5.5 V; see
Figure 7
V
CC
= 5.5 V; see
Figure 8
V
I
= 5.5 V or GND;
V
SW
= GND or V
CC
;
V
CC
= 1.65 V to 5.5 V
pin S; V
I
= V
CC
- 0.6 V;
V
CC
= 5.5 V;
V
SW
= GND or V
CC
-
-
-
-
±0.1
±0.1
±0.1
0.1
[2]
[2]
[2]
ΔI
CC
additional
supply current
input
capacitance
[2]
-
5
500
-
500
μA
C
I
74LVC1G3157
-
2.5
-
-
-
pF
All information provided in this document is subject to legal disclaimers.
As the title says, I know that zone 7 in our community is the gas alarm zone, zone 8 is the emergency help button, and I don't know the others. I hope an expert can answer what zones 1-6 are....
The DSP emulator is different from the MCU. There is no DSP in the emulator. It provides the IEEE standard JTAG port to simulate and debug the DSP. Therefore, the emulator must have a simulation objec...
The NXP Rapid IoT source code is very rich. Although I know that FreeRTOS is used, the code nesting is extremely complex, which makes it difficult to analyze. So if you want to use FreeRTOS's own vTas...