2381 66. 5...3/PTCCL..H...HBE
Vishay BCcomponents
265 V PTC Thermistors
For Overload Protection
FEATURES
•
Wide range of trip and non-trip currents:
From 11 mA up to 800 mA
•
Small ratio between trip and non-trip currents
(I
t
/I
nt
= 1.5 at 25 °C)
•
High maximum inrush current (up to 5.5 A)
•
Leaded parts withstand mechanical stresses
and vibration
•
UL file E148885 according to XGPU standard UL1434
•
UL approved PTCs are guaranteed to withstand severe
test programs
• Long-life cycle tests (over 5000 trip cycles)
• Long-life storage tests (3000 h at 250 °C)
• Electrical cycle tests at low ambient temperatures
(- 40 °C or 0 °C)
• Damp-heat and water immersion tests
• Overvoltage tests at up to 200 % of rated voltage
•
Compliant to RoHS directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
APPLICATIONS
Over-temperature/over-load protection:
•
Telecommunications
•
Automotive systems
•
Industrial electronics
•
Consumer electronics
•
Electronic data processing
QUICK REFERENCE DATA
PARAMETER
Holding current
Resistance at 25 °C (R
25
)
I
max.
Switch temperature
Maximum voltage (RMS or DC)
Operating temperature range
at max. voltage
Climatic category
VALUE
0.011 to 0.8
2.1 to 3000
0.8 to 5.5
140
265
UNIT
A
Ω
A
°C
V
DESCRIPTION
These directly heated thermistors have a positive
temperature coefficient and are primarily intended for
overload protection. They consist of a metallized ceramic
disk with two tinned brass or copper clad steel leads reflow
soldered to it and coated with a high temperature silicone
lacquer. Leadless disks and leaded disks without coating are
available on request.
MOUNTING
The PTC Thermistors are suitable for processing on
automatic insertion equipment.
Typical soldering
235 °C; duration: 5 s (Pb-bearing)
245 °C, duration: 5 s (Lead (Pb)-free)
Resistance to soldering heat
260 °C, duration: 10 s max.
0 to 70
°C
25/125/56
MARKING
Only the grey lacquered thermistors with a diameter of
8.5 mm to 20.5 mm are marked with BC,
R
25
value (example
1R9) on one side and I
nt
, V
max.
on the other side.
Document Number: 29087
Revision: 18-Aug-09
For technical questions, contact:
nlr@vishay.com
www.vishay.com
25
2381 66. 5...3/PTCCL..H...HBE
Vishay BCcomponents
265 V PTC Thermistors
For Overload Protection
ELECTRICAL DATA AND ORDERING INFORMATION
for 2381 66. 5...3; max. voltage = 265 V (AC or DC)
(1)
CATALOG NUMBERS
I
res
MAX.
I
t
I
nt
I
(2)
R
25
DISSIP.
ØD
at V
max.
MAX.
MIN.
MAX.
FACTOR
MAX.
± 20 %
at 25 °C
at 25 °C
BULK
TAPE ON REEL
at 25 °C
and 25 °C
(mW/K)
(mm)
(Ω)
(mA)
(mA)
(mA)
(mA)
11
17
3000
80
6.5
7.3
5
2381 660 51193
2381 660 61193
15
23
1900
110
6.5
7.3
5
2381 660 51593
2381 660 61593
19
29
1200
140
6.5
7.3
5
2381 660 51993
2381 660 61993
28
42
500
200
6.8
7.3
5
2381 660 52893
2381 660 62893
39
59
260
300
6.8
7.3
5
2381 660 53993
2381 660 63993
63
95
120
450
7
7.3
5
2381 660 56393
2381 660 66393
76
115
85
550
7
7.3
5
2381 660 57693
2381 660 67693
95
143
56
600
7
7.3
5
2381 660 59593
2381 660 69593
110
165
48
650
7.5
8.3
7
2381 661 51113
2381 661 61113
140
210
29
800
8
8.3
7
2381 661 51413
2381 661 61413
170
255
22
900
9
9
8.5
2381 661 51713
2381 661 61713
190
285
18
1000
9.5
9
8.5
2381 661 51913
2381 661 61913
210
315
17
1300
10
10.5
10.5
2381 662 52113
2381 662 62113
250
375
12
1500
11
10.5
10.5
2381 662 52513
2381 662 62513
280
420
11
1800
12
11.7
12.5
2381 662 52813
2381 662 62813
320
480
8.4
2200
13
11.7
12.5
2381 662 53213
2381 662 63213
400
600
6.6
3000
15
15.5
16.5
2381 663 54013
-
490
735
4.4
3500
16
15.5
16.5
2381 663 54913
-
590
855
4
4500
19.5
19.8
20.5
2381 664 55913
-
700
1050
2.8
5500
21
19.8
20.5
2381 664 57013
-
(3)
800
1200
2.1
5500
22.5
19.8
20.5
2381 664 58013
-
Notes
(1)
The thermistors are clamped at the seating plane
(2)
I
max.
is the maximum overload current that may flow through the PTC when it passes from the low ohmic to the high ohmic state.
UL approval: I
max.
x 0.75
(3)
Not UL approved
SAP AND 12NC PART NUMBERS
12NC
2381 660 x1193
2381 660 x1593
2381 660 x1993
2381 660 x2893
2381 660 x3993
2381 660 x6393
2381 660 x7693
2381 660 x9593
2381 661 x1113
2381 661 x1413
2381 661 x1713
SAP CODING
PTCCL05H110HyE
PTCCL05H150HyE
PTCCL05H190HyE
PTCCL05H280HyE
PTCCL05H390HyE
PTCCL05H630HyE
PTCCL05H760HyE
PTCCL05H950HyE
PTCCL07H111HyE
PTCCL07H141HyE
PTCCL09H171HyE
12NC
2381 661 x1913
2381 662 x2113
2381 662 x2513
2381 662 x2813
2381 662 x3213
2381 663 54013
2381 663 54913
2381 664 55913
2381 664 57013
2381 664 58013
SAP CODING
PTCCL09H191HyE
PTCCL11H211HyE
PTCCL11H251HyE
PTCCL13H281HyE
PTCCL13H321HyE
PTCCL17H401HBE
PTCCL17H491HBE
PTCCL21H591HBE
PTCCL21H701HBE
PTCCL21H801HBE
Notes
• For bulk parts replace x by “5” and y by “B”
• For taped on reel parts replace x by “6” and y by “T”
CURRENT DEVIATION AS A FUNCTION OF THE AMBIENT TEMPERATURE
250
%
200
I
t
150
I
nt
100
I
max
50
0
- 50
- 25
0
25
50
75
T
amb
(°C)
100
www.vishay.com
26
For technical questions, contact:
nlr@vishay.com
Document Number: 29087
Revision: 18-Aug-09
2381 66. 5...3/PTCCL..H...HBE
265 V PTC Thermistors
For Overload Protection
120
100
80
60
40
20
0
- 50
Vishay BCcomponents
VOLTAGE DERATING AS A FUNCTION OF AMBIENT TEMPERATURE
V
max.
(%)
- 25
0
25
50
75
100
125
150
200
175
T
amb
(°C)
ELECTRICAL CHARACTERISTICS I
max.
AS A FUNCTION OF VOLTAGE
200
I
max
(%)
150
100
80
0
40 50
70
100
120
150
V
rated
(%)
I
max.
as stated in the electrical data and ordering information tables, is the maximum overload current that may flow through the
PTC when passing from the low ohmic to high ohmic state at rated voltage.
When other voltages are present after tripping, the I
max.
value can be derived from the above I
max.
as a function of voltage graph.
Voltages below V
rated
will allow higher overload currents to pass the PTC.
TYPICAL TRIP-TIME AS A FUNCTION OF TRIP CURRENT RATIO
10
3
t
s
10
2
Curve 1: Ø D
max.
= 20.5 mm
Curve 2: Ø D
max.
= 16.5 mm
Curve 3: Ø D
max.
= 12.5 mm
Curve 4: Ø D
max.
= 10.5 mm
Curve 5: Ø D
max.
= 8.5 mm
(1)
(2)
(3)
(4)
(5)
(6)
(7)
10
Curve 6: Ø D
max.
= 7.0 mm
Curve 7: Ø D
max.
= 5.0 mm
Measured in accordance with
“IEC 60738”.
1
10
-1
1
2
4
6
8
10
12
14
I
t
/I
nt
16
Trip-time or switching time (t
s
)
To check the trip-time for a specific PTC, refer to the Electrical Data and Ordering Information tables for the value Int. Divide the
overload or trip current by this Int and you realize the factor It/Int. This rule is valid for any ambient temperature between 0 °C
and 70 °C. Adapt the correct non-trip current with the appropriate curve in the Current Deviation as a Function of the Ambient
Temperature graph. The relationship between the It/Int factor and the switching time is a function of the PTC diameter; see the
above graphs.
Example
What will be the trip-time at I
ol
= 0.8 A and T
amb
= 50 °C of a thermistor type 2381 661 51713; 22
Ω;
Ø D
max.
= 8.5 mm:
I
nt
from the table: 170 mA at 25 °C
I
nt
: 170 x 0.87 = 148 mA (at 50 °C).
Overload current = 0.8 A; factor I
t
/I
nt
:
0.8
/
0.148
= 5.40. In the typical trip-time as a function of trip current ratio graph, at the 8.5 mm
line and I
t
/I
nt
= 5.40, the typical trip-time is 3.0 s.
Document Number: 29087
Revision: 18-Aug-09
For technical questions, contact:
nlr@vishay.com
www.vishay.com
27
2381 66. 5...3/PTCCL..H...HBE
Vishay BCcomponents
265 V PTC Thermistors
For Overload Protection
COMPONENTS OUTLINE
CODE NUMBER 2381
660
661
662
663
664
D
5...3
6...3
5...3
6...3
5...3
62113 - 62513
62813 - 63213
5...3
5...3
T
SPQ
500
1500
250
1500
200
1500
750
100
50
OUTLINE
Fig. 1a
Fig. 1b
Fig. 1a
Fig. 1b
Fig. 1a
Fig. 1b
Fig. 1c
Fig. 1a
Fig. 1a
PTC THERMISTORS IN BULK
DIMENSIONS OF BULK TYPE PTC’S
(in mm)
D
d
H3
H2
See table
0.6 ± 10 %
5.5 max.
4.0 ± 1.0
D + 5 max.
20 min.
5.0
T
H2
F
L1
d
H3
L1
F
Fig. 1a
PTC THERMISTORS ON TAPE ON REEL
P
D
P
P
h
T
h
D
P
P
P
h
T
h
H3
d
W2
L
H3
d
W2
L
W0 W1 W
H0 H1
H2
H2
W0 W1 W
H0 H1
P0
P1
F
T
1
D0
t
P0
P1
F
T
1
D0
t
Fig. 1b
Fig. 1c
TAPE AND REEL ACCORDING TO IEC 60286-2
dimensions in millimeters
SYMBOL
D
d
P
F
H0
H2
H3
H4
T
www.vishay.com
28
PARAMETER
Body diameter
Lead diameter
Pitch of components
Diameter < 12 mm
Diameter
≥
12 mm
Leadcenter to leadcenter distance
(between component and tape)
Lead wire clinch height
Component bottom to seating plane
Component top to seating plane
Seating plane difference (left-right lead)
Total thinkness
DIMENSIONS
See table
0.6
12.7
25.4
5.0
16.0
4.0
D+5
0
5.5
TOLERANCE
max.
± 10 %
± 1.0
± 2.0
+ 0.6
- 0.1
± 0.5
± 1.0
max.
± 0.2
max.
Document Number: 29087
Revision: 18-Aug-09
For technical questions, contact:
nlr@vishay.com
2381 66. 5...3/PTCCL..H...HBE
265 V PTC Thermistors
For Overload Protection
TYPICAL RESISTANCE/TEMPERATURE
CHARACTERISTIC
10
8
10
7
10
6
10
5
10
4
10
3
10
2
2381 660 52893
PTCCL05H280HBE
2381 660 51193
PTCCL05H110HBE
2381 660 51593
PTCCL05H150HBE
Vishay BCcomponents
TYPICAL RESISTANCE/TEMPERATURE
CHARACTERISTIC
10
8
10
7
10
6
Resistance [Ω]
10
5
2381 660 56393
PTCCL05H630HBE
2381 660 53993
PTCCL05H390HBE
Resistance [Ω]
2381 660 51993
PTCCL05H190HBE
10
4
10
3
10
2
2381 660 59593
PTCCL05H950HBE
2381 660 57693
PTCCL05H760HBE
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
10
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
TYPICAL RESISTANCE/TEMPERATURE
CHARACTERISTIC
10
7
10
6
10
5
Resistance [Ω]
10
4
10
3
10
2
10
1
2381 661 51913
PTCCL09H191HBE
2381 661 51113
PTCCL07H111HBE
TYPICAL RESISTANCE/TEMPERATURE
CHARACTERISTIC
10
6
10
5
10
4
10
3
10
2
10
1
2381 662 52113
PTCCL11H211HBE
Resistance [Ω]
2381 661 51413
PTCCL07H141HBE
2381 662 52513
PTCCL11H251HBE
2381 661 51713
PTCCL09H171HBE
2381 662 52813
PTCCL13H281HBE
2381 662 53213
PTCCL13H321HBE
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
TYPICAL RESISTANCE/TEMPERATURE
CHARACTERISTIC
10
6
10
5
TYPICAL RESISTANCE/TEMPERATURE
CHARACTERISTIC
10
6
10
5
10
4
10
3
10
2
10
2381 664 57013
PTCCL21H701HBE
2381 664 55913
PTCCL21H591HBE
Resistance [Ω]
10
3
10
2
2381 663 54013
PTCCL17H401HBE
10
2381 663 54913
PTCCL17H491HBE
Resistance [Ω]
10
4
1
1
2381 664 58013
PTCCL21H801HBE
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
0 25 50 75 100 125 150 175 200 225 250
Temperature [°C]
Document Number: 29087
Revision: 18-Aug-09
For technical questions, contact:
nlr@vishay.com
www.vishay.com
29