Features ....................................................................................................................................................................................... 1
Typical Phase Jitter (70 fs RMS) and Phase Noise Data ............................................................................................................. 2
Ordering Information .................................................................................................................................................................... 3
LVPECL and FlexSwing Termination .................................................................................................................................. 19
LVDS, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 20
HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 20
Low-power HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V .................... 20
Dimensions and Patterns ― 2.0 x 1.6 mm x mm ....................................................................................................................... 21
Dimensions and Patterns ― 2.5 x 2.0 mm x mm ....................................................................................................................... 22
Dimensions and Patterns ― 3.2 x 2.5 mm x mm ....................................................................................................................... 23
Revision History ......................................................................................................................................................................... 24
Rev 0.54
Page 4 of 25
www.sitime.com
SiT9501
Ultra-low Jitter Differential XO for Standard Networking Frequencies
Electrical Characteristics
ADVANCED
All Min and Max limits in the Electrical Characteristics tables are specified over operating temperature and rated operating
voltage with standard output termination shown in the termination diagrams. Typical values are at 25°C and nominal
supply voltage.
Table 3. Electrical Characteristics – Common to All Output Signaling Types
Parameter
Output Frequency Range
Symbol
f
Min.
Typ.
Max.
Unit
MHz
Condition
Refer to frequencies listed in
Error! Not a valid result for table.
s
ection.
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and 10 years
aging at 25°C
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and first year aging
at 25°C
Ambient temperature of 25°C
Extended commercial, ambient temperature
Industrial, ambient temperature
Ambient temperature
Extended industrial, ambient temperature
Voltage-supply order code “YY”
Voltage-supply order code “XX”
Voltage-supply order code “18”.
Contact SiTime
for 1.5 V
Voltage-supply order code “25”
Voltage-supply order code “33”
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
See
Figure 6
and
Figure 8
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin toggles to enable logic level to
the time clock pins reach 90% of swing. See
Figure 13
Measured from the time OE pin toggles to disable logic level to
the last clock edge. See
Figure 14
12 kHz to 20 MHz offset frequency integration bandwidth
1. OverviewSSDP Simple Service Discovery Protocol, which is one of the core protocols of UPnP. UPnP is a zero-configuration network protocol. Home devices used by the public generally support this pro...
SL3036 is a switch step-down DC-DC that supports wide voltage input. The chip has a built-in 100V/5A power MOS and a maximum input voltage of 90V. SL3036 has the characteristics of low standby power c...
The data sheet says that the SST25VF016B SuperFlash memory array consists of uniform 4 KB erasable sectors, 32 KB overlay blocks, and 64 KB overlay erasable blocks. How should we understand the overla...
In the study of electronic circuits, to learn how to analyze circuits, we must start by understanding the three states of circuits. The three states of circuits are: open circuit (load), short circuit...
Recently, the discussion about pure vision-based intelligent driving solutions has been quite heated, with everyone arguing with each other. In fact, the core debate is only one: whether cameras ca...[Details]
element14 Community launches 2022 holiday celebrations for engineers and STEM groups Community members can participate in element14 holiday giveaways, hackathons and many other celebratory events ...[Details]
1. Impact of temperature on the performance and life of communication switching power supplies
The main component of the communication switching power supply is the high-frequency switching rectifi...[Details]
December 2, 2021, Beijing - Today,
Graphcore
(to be announced) officially announced the latest results of its participation in the MLPerf test. The results show that compared with the first...[Details]
For hexagonal nuts, the commonly used standards are: GB52, GB6170, GB6172 and DIN934. The main differences between them are: GB6170 is thicker than GB52, GB6172 and DIN934, commonly known as thick ...[Details]
With the development of generative artificial intelligence represented by ChatGPT, end-to-end autonomous driving systems have received widespread attention and are expected to bring revolutionary b...[Details]
1. The role of electronic transformers in power supply technology
Electronic transformers, semiconductor switching devices, semiconductor rectifier devices, and capacitors a...[Details]
Beijing time on March 31, people familiar with the matter said that Tesla is seeking to build a new battery factory in the United States and is cooperating with Chinese battery giant CATL, an arrange...[Details]
Friends who have done their own renovations must know that if you ask which room in the house is the most expensive to renovate, it must be the bathroom. In fact, the bathroom is usually the s...[Details]
Industrial controllers are electronic devices used to control and monitor equipment and machines in industrial production processes. They are widely used in various industrial fields, including man...[Details]
Recently, Cixin Technology (Shanghai) Co., Ltd. ("Cixin Technology") announced that it has completed an angel++ round of financing of over 100 million yuan, led by Shunwei Capital, followed by Qiming...[Details]
Use STM8 development environment: IAR for STM8 Use TIM1_CH3 to output PWM wave, the output pin is PD5 The microcontroller used is STM8L151 For STM8L, the default clock source is off and needs to be...[Details]
In the previous section, S3C2440 transplantation of uboot: trimming and modifying default parameters trimmed uboot and modified the default parameters. This section starts to make yaffs image and pat...[Details]
Preface
Laser Measurement - Applications in the Railway Industry
1. Overview
The OPTIMESS laser displacement sensor installed on the trackside can measure the position of the...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
