Has anyone used the SKY1311T card reader chip? I know the SPI protocol, but I don't know how to start writing it. I don't have any ideas. I hope someone can give me some advice, or if there is a sampl...
The CC2652R device is a multiprotocol wireless 2.4GHz MCU targeting Thread, Zigbee, Bluetooth 5 low energy, IEEE 802.15.4g, smart objects with IPv6 (6LoWPAN), Wi-SUN and proprietary systems including ...
How is this upper computer software made? Can anyone tell me what software is used to make it?
It would be best if you could provide a software download link. How was this brother monitoring module de...
6678 reads and writes EEPROM through SPI interface. EEPROM needs to be write-enabled before writing. Write-enabled requires writing instruction 0x06 first, and requires CS to be pulled high after the ...
As shown in the figure, the three red components in the schematic diagram of the product on the right are not included in the reference circuit. What are the functions of these components? How to sele...
Affected by the COVID-19 pandemic this year, mobile phone manufacturers have chosen to release new products online live. OnePlus' annual flagship will be officially unveiled in April. As OnePlus mobi...[Details]
1. Evolution trend of intelligent driving domain control hardware solutions 2. The current mainstream intelligent driving domain control hardware solution is N*SoC+MCU, so can the MCU be removed? ...[Details]
OFweek Cup · OFweek 2023 China
Robot
Industry Annual Selection (abbreviated as OFweek Robot Awards 2023) is jointly organized by OFweek, China's high-tech industry portal, and its authorita...[Details]
In some special applications, MCU communication cannot use wired data transmission, but needs to use short-distance wireless data transmission. Short-distance wireless transmission has the advantages ...[Details]
During the Fifth Future Network Development Conference, Baidu CTO Wang Haifeng shared the new features of AI technology in accelerating its implementation in industry practices. Wang Haifeng pointed ...[Details]
1. External interrupt 0, 1; caused by the level signal of pin /INT0, /INT1 respectively. 2. Timer/Counter 0, 1; caused by the overflow of T0, T1 respectively. 3. Serial port sending, receiving; c...[Details]
Toshiba’s latest Visconti™ ADAS SoC targets automakers’ autonomous driving applications, with high-density Semper NOR Flash memory family enhancing functional safety for the SoC Cypress Semiconduct...[Details]
It is impossible for a dual-NIC computer to have two gateways, because there can only be one default gateway. Install two NICs on the server, set different IPs and gateways (intranet and extranet) res...[Details]
In electrical measurements, synchronization is the process of accurately matching measurement data so that they start from essentially the same moment in time. Synchronization is required when there ...[Details]
As the hot summer approaches, various
naked-eye 3D
mobile
terminals in electronic stores or online shops have also become popular. Patriot's naked-eye 3D movie book, naked-eye 3D Moonl...[Details]
In some DC/DC converters, on-chip cycle-by-cycle current limiting may not be sufficient to prevent failure during a short circuit. A nonsynchronous boost converter provides a direct path from the inpu...[Details]
1 Introduction
Home service robots are the development direction of robots and a breakthrough for my country to further strengthen its research on robot technology. Home service robots are des...[Details]
(1) Detection method. When the voltage to be measured exceeds the maximum voltage limit of the multimeter, whether it is DC voltage or AC voltage, the resistor voltage divider in Figure 5-1 can be ...[Details]
SACD (Super Audio CD)
1. SACD Introduction
1. What is SACD?
The advent of the CD can be considered one of the most exciting events in the field of music reproduction, bringing musical per...[Details]
Industrial control voltage generally refers to the voltage used to control industrial equipment and machinery. In the industrial field, the control voltage can be direct current (DC) or alternating...[Details]