L: output is low level (weak pull down) oscillation stops
SiTime Corporation
Rev. 1.04
990 Almanor Avenue, Suite 200
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised Sept. 19, 2008
SiT8002
Description
The SiT8002 oscillator family is composed of the world’s
smallest, high-performance programmable oscillators. The
SiT8002 is suitable for use in clock generation for consumer,
portable, industrial, automotive, and computation applications.
This oscillator family is packaged in standard low-cost plastic
QFN-type IC packages with footprints that match common
quartz surface mount products.
MEMS resonators are 1000x smaller by volume than quartz
resonators and are built in high volume CMOS fabs instead of
small custom manufacturing facilities. Due to their small size,
massive lot sizes, and simpler manufacturing processes
MEMS oscillators are inherently more reliable, have more
consistent performance and are always in stock.
The SiT8002, by eliminating the quartz crystals, has improved
immunity to the environmental effects of vibration, shock,
strain, and humidity.
To order samples, go to www.sitime.com and click on Request
Sample” link.
Absolute Maximum Ratings
Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual
performance of the IC is only guaranteed within the operational specifications not absolute maximum ratings.
Ab
solute Maximum Table
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Theta JA ( with copper plane on VDD and GND)
Theta JC (with PCB traces of 0.010 inch to all pins)
Soldering Temperature (follow standard Pb free soldering guidelines)
Number of Program Writes
Program Retention over -40 to 125C, Process, VDD (0 to 3.6V)
–
–
Min.
-65
-0.5
Max.
150
+3.65
6000
75
24
260
1
1,000+
Unit
°C
V
V
°C/W
°C/W
°C
NA
years
Operating Conditions
Parameter
Supply Voltages, VDD
[1]
Min.
2.97
2.25
1.7
Typ.
3.3
2.5
1.8
-
-
-
-
Max.
3.63
2.75
1.9
70
85
15
200
Unit
V
V
V
°C
°C
pF
ms
Extended Commercial OperatingTemperature
Industrial Operating Temperature
Maximum Load
Capacitance
[2]
VDD Ramp Time
-20
-40
-
0
Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensibility Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Notes:
1. The 2.5V device can operate from 2.25V to 3.63V with higher output drive, however, the data sheet parameters cannot be guaranteed. Please contact factory for
this option.
2. The output driver strenght can be programmed to drive up to 30pF load. Please contact factory for this option.
Page 2 of 7
SiT8002
DC Electrical Specifications
@VDD = 3.3V ±10%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -9 mA
IOL = 9 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
22
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
@VDD = 2.5V ±10%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -7 mA
IOL = 7 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
22
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
@VDD = 1.8V ±5%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -5 mA
IOL = 5 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
19
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
Page 3 of 7
SiT8002
AC Electrical Specifications
@VDD = 3.3V ±10%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency
Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1 MHz to 125 MHz
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-30
-50
-100
-
45
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+30
+50
+100
1
55
2.0
2.0
±98
±60
Unit
MHz
ppm
ppm
ppm
ppm
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
@VDD = 2.5V ±10%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1MHz to 125MHz
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-30
-50
-100
-
45
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+30
+50
+100
1
55
2.0
2.0
±130
±60
Unit
MHz
ppm
ppm
ppm
ppm
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
@VDD = 1.8V ±5%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency
Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1 MHz to 65MHz
Output frequency= 65 MHz to 125MHz
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-50
-100
-
45
40
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+50
+100
1
55
60
2.0
2.0
±185
±100
Unit
MHz
ppm
ppm
ppm
%
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Notes:
3. ±30 ppm is available only over extended commercial temperature range from-20 °C to +70 °C and VDD=2.5V or 3.3V.
I am planning to use the LM2611 chip recently, but some things are not specified in its data sheet, such as the calculation formula for the output voltage and the voltage drop. Does anyone know?...
[backcolor=rgb(222, 240, 251)]I use STM32F767 to drive a 7-inch screen, but it always doesn't display. [/backcolor] [backcolor=rgb(222, 240, 251)]Screen information:[/backcolor][backcolor=rgb(222, 240...
Analog IC Design Qingyuan Yang (National Chung Hsing University, Taiwan) : https://training.eeworld.com.cn/course/6036An introduction and analysis of university advanced electronic circuit courses.Com...
There was a problem when controlling the PMOS at high frequency. A 5V, 62.5KHZ sine wave signal was input to the base control terminal of the transistor, and a sine wave signal could also be measured ...
Recently, Jiali Chuang only charges 5 yuan for 5 sample boards (within 10*10cm), and each person can make 2 samples per month, so I drew a PCB ruler as a souvenir for my roommates and friends. It cont...
01 Before the troops move, food and fodder must be sent first
Thanks to the forum and the developer for giving me this review opportunity. I have wanted to try out National Technology for a long time,...
Xiaopeng Motors has recently encountered a problem of "charging pile outage". Who is responsible? On the evening of August 31, a Xiaopeng car owner revealed that Xiaopeng Motors’ charging piles at ...[Details]
China Energy Storage Network reported
: "With the large-scale development of clean energy and the increasing proportion of electricity in terminal energy consumption, it is expected that in 2...[Details]
The source program of the PIC series microcontroller refers to the program written in the mnemonic instructions of the PIC (assembly language program). Here we will briefly introduce the format r...[Details]
Samsung has been a global Olympic partner for more than 20 years, and in 2018, it signed a 10-year extension agreement. For this reason, Samsung releases Olympic special editions of its current...[Details]
In life, the battery capacity of our mobile phones and computers will decay, and the battery of new energy vehicles will also decay. Due to the characteristics of lithium batteries, general car owner...[Details]
TCL is preparing to launch a new 5G mid-range phone early next year, and the whistleblower @Evan Blass has announced some of the parameters and appearance of the phone, which will be called TCL 20 ...[Details]
1. Introduction to C8051F development software: name of software type Introduction Official website Silicon IDE IDE, C, assembly compiler Free software, Silicon Integrated Development Environment ...[Details]
During the mortar live-fire shooting, it is common for mortar shells to misfire. If a mortar shell does not fire, it is strictly forbidden to reload the shell. If reloading, it is easy to cause a cha...[Details]
A three-op-amp IA can achieve high common-mode rejection by using perfectly matched resistors around the differential amplifier, but the feedback architecture of this IA can significantly reduce the ...[Details]
All-solid-state batteries are considered to be the real power batteries for the next generation of electric vehicles. Compared with the currently widely used lithium batteries, they charge faster, hav...[Details]
1 Introduction
In recent years, my country's power communication network has developed rapidly. However, the corresponding monitoring, control and maintenance capabilities are relatively b...[Details]
In the case of the Apple
iPhone
and related products, the concept is to build the user
interface
first
—the capacitive touch screen—and then leverage the underlying hardware and sup...[Details]
Preface
In the field of medical care and health care, the extensive use of ultra-low power consumption and miniaturized wireless transceiver chips and sensors implanted/invasively or worn on t...[Details]
introduction In the existing CNC system, the computer CNC system solution of industrial computer plus motion control card is mostly used to design the motion controller. As the overall functions of i...[Details]
Embedded voice playback systems are increasingly widely used. There are several methods for playing Chinese voice, including recording chip method, voice synthesis chip method and Chinese voice lib...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
