*Results may vary. Additional terms and conditions, including the limited warranty, apply at the time of purchase.
See the warranty details and enclosed information for applicable operating and use requirements.
Page 1
Document number: 1017119.3
maxwell.com
DATASHEET
56V MODULE
PRODUCT SPECIFICATIONS (Cont’d)
PHYSICAL
Mass, typical
Power Terminals
Recommended Torque - Terminal
Vibration Specification
Shock Specification
Environmental Protection
Cooling
BMOD0130 P056 B03
18 kg
M8/M10
20/30 Nm
Telcordia GR-63-CORE Zone 4
N/A
IP30
Natural Convection
N/A
N/A
Overvoltage Alarm
Deutsch DTM
Passive
2,600 W/kg
5,400 W/kg
3.1 Wh/kg
57 Wh
MONITORING / CELL VOLTAGE MANAGEMENT
Internal Temperature Sensor
Temperature Interface
Cell Voltage Monitoring
Connector
Cell Voltage Management
POWER & ENERGY
Usable Specific Power, P
d4
Impedance Match Specific Power, P
max5
Specific Energy, E
max6
Stored Energy
7
SAFETY
Short Circuit Current, typical
Certifications
High-Pot Capability
10
(Current possible with short circuit from rated voltage.
Do not use as an operating current.)
6,900 A
RoHS, UL810a (750 V)
4,000 V DC
Page 2
Document number: 1017119.3
maxwell.com
DATASHEET
56V MODULE
TYPICAL CHARACTERISTICS
THERMAL CHARACTERISTICS
Thermal Resistance
(R
ca,
All Cell Cases to Ambient), typical
8
BMOD0130 P056 B03
0.50
o
C/W
16,000 J/
o
C
61 A, RMS
99 A, RMS
Thermal Capacitance
(C
th
), typical
Maximum Continuous Current (ΔT = 15
o
C)
8
Maximum Continuous Current (ΔT = 40
o
C)
8
LIFE
DC Life at High Temperature
1
Capacitance Change
ESR Change
(held continuously at Rated Voltage & Maximum Operating
Temperature)
(% decrease from minimum initial value)
(% increase from maximum initial value)
8 years
20%
100%
14 years
20%
100%
4 years
Projected DC Life at 25°C
1
(held continuously at Rated Voltage)
Capacitance Change
ESR Change
(% decrease from minimum initial value)
(% increase from maximum initial value)
Shelf Life
(Stored uncharged at 25°C)
Page 3
Document number: 1017119.3
maxwell.com
DATASHEET
56V MODULE
ESR AND CAPACITANCE VS TEMPERATURE
180%
170%
160%
150%
140%
130%
120%
110%
100%
90%
80%
-60
-40
-20
0
20
40
60
80
Temperature (°C)
Capacitance
DC ESR
Percentage change from value at 25°C
NOTES
1. Capacitance and ESR
DC
measured at 25°C using
specified test current per waveform below.
2. Absolute maximum voltage, non-repeated. Not to
exceed 1 second.
3. After 72 hours at rated voltage. Initial leakage current
can be higher.
0.12V
2
4. Per IEC 62391-2, P
d
= ESR
DC
x mass
V
2
5. P
max
= 4 x ESR x mass
DC
½ CV
2
6. E
max
=
3,600 x mass
2
7. E
stored
= ½ CV
3,600
8. ∆T=I
RMS2
x ESR x R
ca
9. Per United Nations material classification UN3499, all
Maxwell ultracapacitors have less than 10 Wh capacity
to meet the requirements of Special Provisions
361. Both individual ultracapacitors and modules
composed of those ultracapacitors shipped by
Maxwell can be transported without being treated
as dangerous goods (hazardous materials) under
transportation regulations.
10. Duration = 60 seconds. Not intended as an operating
parameter.
Page 4
Document number: 1017119.3
maxwell.com
DATASHEET
56V MODULE
MOUNTING RECOMMENDATIONS
4
3
Please refer to the user manual for installation
recommendations.
D
MARKINGS
2
1
Products are marked with the following information:
Rated capacitance, rated voltage, product number,
name of manufacturer, positive and negative terminal,
warning marking, serial number.
D
BMOD0130 P056 B03
M10 NEGATIVE
TERMINAL
M8 POSITIVE
TERMINAL
312.8±2.0
BMOD0130 P056 BO3 MONITOR
CABLE ONLY, 150 MIN
LEFT SIDE
218.2 1.0
20.0±1.0
TYP.
C
175
MAX
C
H
74.9 2
T
BRASS
INSERT
FACE
100.0±2.0
5.1±1.0
17.0±2.0
B
22
135.0 1.0
RIGHT SIDE
218.2 1.0
683 MAX
149.1±2.0
5.1±1.0
32.2±2.0
L
70.6 1.0
B
177 MAX
652.2±3.0
TYPICAL WIDTH FROM
BRASS INSERT FACE
W
Part Description
BMOD0130 P056 B03
A
BRASS INSERT
FACE
L (max)
683
Dimensions (mm)
W (max)
H (max)
177
175
T (±2mm)
74.9
Package Quantity
1
A
BOTTOM
164.3±1.5
TYPICAL WIDTH FROM
BRASS INSERT FACE
SCALE
B 68911
1:5
SIZE
CAGE CODE
PART NO.
108880, 109358
REV
REV
2
DOC. NO.
1017268
2
SHEET
2 OF 2
4
B-PG1 REV A 7/01
3
2
1
Product dimensions are for reference only unless otherwise identified. Product dimensions and specifications may change without notice.
Please contact Maxwell Technologies directly for any technical specifications critical to application. All products featured on this datasheet are covered by the following
U.S. patents and their respective foreign counterparts: 6643119, 7295423, 7342770, 7352558, 7384433, 7440258, 7492571, 7508651, 7791860, 7791861, 7859826, 7883553,
7935155, 8072734, 8098481, 8279580, and patents pending.
Maxwell Technologies, Inc.
Global Headquarters
3888 Calle Fortunada
San Diego, CA 92123
USA
Tel: +1 858 503 3300
Fax: +1 858 503 3301
Maxwell Technologies SA
Route de Montena 65
CH-1728 Rossens
Switzerland
Tel: +41 (0)26 411 85 00
Fax: +41 (0)26 411 85 05
Maxwell Technologies, GmbH
Leopoldstrasse 244
80807 München
Germany
Tel: +49 (0)89 / 4161403 0
Fax: +49 (0)89 / 4161403 99
Maxwell Technologies
Shanghai Trading Co. Ltd.
Unit A2,C 12th Floor
Huarun Times Square
500 Zhangyang Road,
Pudong New Area
Shanghai 200122,
P.R. China
Phone: +86 21 3852 4000
Fax: +86 21 3852 4099
Maxwell Technologies Korea, Ltd.
Room 1524, D-Cube City
Office Tower, 15F #662
Gyeongin-Ro, Guro-Gu,
Seoul, 152-706
South Korea
Phone: +82 10 4518 9829
MAXWELL TECHNOLOGIES, MAXWELL, MAXWELL CERTIFIED INTEGRATOR, ENABLING ENERGY’S FUTURE, BOOSTCAP, C CELL, D CELL and their respective
designs and/or logos are either trademarks or registered trademarks of Maxwell Technologies, Inc. and may not be copied, imitated or used, in whole or in
京公网安备 11010802033920号
EEWORLD
