AME8550AEFTA300Z datasheet, PDF

Datasheet> All Categories > Power/power management> The power supply circuit> AME8550AEFTA300Z

AME8550AEFTA300Z: DescriptionVoltage Detector; CategoryPower/power management The power supply circuit; File Size165KB，21 Pages; ManufacturerAnalogMicroElectronics,Inc.(AME); AMT was founded in Taiwan in November 2000 and merged into AMT Microelectronics, Inc., a US company located in Silicon Valley, California, USA. Its stock was officially listed for public trading in March 2004.

Download Datasheet Parametric View All

AME8550AEFTA300Z Overview

Voltage Detector

AME8550AEFTA300Z Parametric

Parameter Name	Attribute value
Maker	AnalogMicroElectronics,Inc.(AME)
package instruction	,
Reach Compliance Code	compli

AME8550AEFTA300Z Preview

Download Datasheet

View All

AME, Inc.

AME8550

Voltage Detector

General Description

The AME8550 series are highly precise, low power con-

sumption voltage detectors, manufactured using CMOS

and fuse trimming technologies. Detect voltage is ex-

tremely accurate with minimal temperature drift.

Both CMOS and N channel open drain output configu-

rations are available.

Functional Block Diagram

(1) CMOS Output without delay

OUT

Vref

Features

Highly accurate: + 2%

Low power consumption: TYP 0.8µA

=1.5V)

Detect voltage range: 1.6V to 6.0V in 0.1V

increments

Operating voltage range: 1.2V to 6.5V

Detect voltage temperature characteristics:

TYP ±100ppm/

Output configuration: N-channel open drain or

CMOS

Ultra small package :

SOT-23 (150mW)

SOT-25 (150mW)

SOT-89 (500mW)

SC-70 (100mW)

Add an external capacitor to perform an

µP

reset.

(2) Nch Open Drain Output without delay

OUT

Vref

(3) CMOS Output with delay

OUT

REF

Vref

Applications

Microprocessor reset circuitry

Memory battery back-up circuits

Power-on reset circuits

Power failure detection

System battery life and charge voltage

monitors

(4) Nch Open Drain Output with delay

OUT

REF

Vref

Recommended Resources

TDA1510A power amplifier circuit diagram

High performance infrared remote control switch circuit

Dynamic constant current load for testing fuel cell batteries

555 lighting ultrasonic remote control circuit

flash alarm circuit

845E computer motherboard circuit diagram_36

PHYTEC's imx8mplus development board review: We received the imx8mplus development board from PHYTEC for evaluation, and last time we had it up, everything was working fine. The official website comes with a paper document for rapid development,...; yijiu98 Toshiba Photorelays TLP3547 Review

[RVB2601 Creative Application Development] 4. Use RTC to record time: [i=s]This post was last edited by hehung on 2022-3-6 19:28[/i]PrefaceRTC is a good choice for recording time. It does not require an external clock chip and can also achieve the purpose of obtaining a...; hehung XuanTie RISC-V Activity Zone

ADN8834 does not work or has current overshoot: 1. ADN8834 power-on probability VREF oscillation causes the chip to not work Oscillation phenomenon; Test conditions: VLIM=0V~0.5V, T=25C, VCC RC: 30ohm, 22nf; ICC=10mA when VERF is normal, abnormal c...; 这个苹果不太挑 Analog electronics

A brief discussion on the bus differences of ARM Cortex-m0/m4 series: Let’s start with a simple question: How fast can the GPIO flip speed of STM32 (for example, used to simulate timing) be? Write a piece of code to test: [code]void test(void) { for(;;) { GPIOA->ODR = (...; cruelfox MCU

Please help me interpret this article about tl431 bias current: https://www.baidu.com/sf_edu_wenku/view/326acdef172ded630b1cb6b7 I don't know where the original post came from. . The first question. . Are α and β equal in the third equation? Otherwise, how did the...; grove_armweak Power technology

Disable automatic layer selection for routing: I would like to ask how to turn off the automatic layer selection function for routing... When I draw a 4-layer board, I select Signal Layer 1 or Signal Layer 2 for routing, but as soon as I click on ...; bluefox0919 PCB Design

Popular Components