OPA651NB datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> OPA651NB

OPA651NB: Part NumberOPA651NB; CategoryAnalog mixed-signal IC Amplifier circuit; File Size8579.33，32 Pages; ManufacturerTexas Instruments; Websitehttp://www.ti.com.cn/

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

OPA651NB Overview

OPA651NB amplifier basic information:

OPA651NB is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are LSSOP, TSOP5/6,.11,37

OPA651NB amplifier core information:

The minimum operating temperature of OPA651NB is -40 °C and the maximum operating temperature is 85 °C. Maximum bias current at 25°C: 10 µA

The maximum slew rate of OPA651NB given by the manufacturer is 7.5 mA. Its minimum voltage gain is 130. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the OPA651NB gain becomes 0.707 times the low-frequency gain is 470000 kHz. The power of OPA651NB is NO. Its programmable power is NO.

The nominal supply voltage of the OPA651NB is 5 V, and its corresponding nominal negative supply voltage is -5 V. The power supply range is: +-5 V. The input offset voltage of OPA651NB is 2000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of OPA651NB:

The width of OPA651NB is: 1.625 mm, and the length is 2.95 mm. OPA651NB has 5 terminals. Its terminal position type is: DUAL. Terminal pitch is 0.95 mm. Total pins: 5

OPA651NB amplifier additional information:

OPA651NB adopts the VOLTAGE-FEEDBACK architecture. It is not a low-bias amplifier. It does not belong to the low offset class of amplifiers. The frequency compensation status of OPA651NB is: YES (AVCL>=2). Its temperature grade is: INDUSTRIAL.

It is not a micropower amplifier. The corresponding JESD-30 code is: R-PDSO-G5. The packaging code of OPA651NB is: LSSOP. The OPA651NB package materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR.

The OPA651NB package pin forms are: SMALL OUTLINE, LOW PROFILE, SHRINK PITCH. Its terminal forms are: GULL WING. The maximum seat height is 1.45 mm.

Recommended Resources

DC low voltage fuse blown indication circuit

555 high-precision regulated power supply circuit

Ring counting circuit

Bathroom automatic exhaust fan

Three-phase motor phase failure protection circuit

DMAl2 main circuit schematic diagram

How to dynamically open the Bluetooth kernel log for the Allwinner V853 chip?: **1. Topic** How to dynamically open the log of the Bluetooth kernel **2. Problem background** Product: Tina product such as scanning pen Hardware: V853 + XR829 Software: Tina linux4.9 The purpose is to analyze the problem and capture the BT_DBG prin...; aleksib Domestic Chip Exchange

XTR111 Application Circuit: I would like to ask, in the XTR111 application circuit, when using BC856 instead of 2N2907 and NDT2955 instead of 2N6804, there is no current output. Are these two irreplaceable? Ensure that the parameters are roughly the same and the pack...; LY105 Analogue and Mixed Signal

Download Qorvo's "Fundamentals of Motor Control": Like many consumer electronics products, consumers expect these products to be lower cost, more reliable, and easier to use. Brushless DC (BLDC) motors help meet these demands. To meet this demand, fully optimized, highly integrated system-on-chip (...; 兰博 RF/Wirelessly

Motor Control Basics - Timer Encoder Mode Usage and Speed Calculation: The previous article (https://bbs.eeworld.com.cn/thread-1157711-1-1.html) introduced the principle of timer capturing input pulses. The principle of that method is to manually switch the rising edge and falling edge capture according to the princip...; DDZZ669 Motor Drive Control（Motor Control）

BLE Protocol Stack UART Debug Guide: The importance of UART in embedded software development is self-evident; I have debugged the serial port of TI BLE protocol stack before, and I remember making a simple document record at that time to indicate the points that need attention. Unfortu...; fish001 Wireless Connectivity

A classic circuit sharing of 5V and 3.3V level conversion of IIC: The following three states should be considered in the operation of the level converter: No device pulls down the bus line. The "low voltage" part of the bus line is pulled up to 3.3V through the pull-up resistor Rp. The gate and source of the...; 灞波儿奔 Analogue and Mixed Signal

OPA651NB Also View