TL061IJG datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> TL061IJG

TL061IJG: Part NumberTL061IJG; CategoryAnalog mixed-signal IC Amplifier circuit; File Size19032.19，51 Pages; ManufacturerTexas Instruments; Websitehttp://www.ti.com.cn/

Alternative parts

Part Number	Manufacturer	Description
LM301AH	Texas Instruments	Operational Amplifier 8-TO-99 0 to 70
TL061MN	STMicroelectronics	OP-AMP, 9000 uV OFFSET-MAX, 1 MHz BAND WIDTH, PDSO8
TL061IH	STMicroelectronics	OP-AMP, 9000uV OFFSET-MAX, 1MHz BAND WIDTH, MBCY8, TO-99, 8 PIN
TL060IP	Texas Instruments	OP-AMP, 9000uV OFFSET-MAX, 1MHz BAND WIDTH, PDIP8, PLASTIC, DIP-8
TL061MU	Texas Instruments	TL061MU是一款OPERATIONAL AMPLIFIER。常用的包装方式为FP-10TL061MU的最低工作温度是-55 °C，最高工作温度是125 °C。25℃下的最大偏置电流为：0.0002...
LM301AD	STMicroelectronics
TL060IJG	Texas Instruments	OP-AMP, 9000uV OFFSET-MAX, 1MHz BAND WIDTH, CDIP8, 0.300 INCH, HERMETIC SEALED, CERAMIC, DIP-8
TL061IN	STMicroelectronics	Operational Amplifiers - Op Amps Single Lo-Power JFET

TL061IJG Overview

Basic information of TL061IJG amplifier:

TL061IJG is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are 0.300 INCH, HERMETIC SEALED, CERAMIC, DIP-8

TL061IJG amplifier core information:

The minimum operating temperature of TL061IJG is -40 °C and the maximum operating temperature is 85 °C. Its peak reflow temperature is NOT SPECIFIED Its maximum bias current at 25°C is: 0.0002 µA Its maximum average bias current is 0.02 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of TL061IJG is 3.5 V/us. The maximum slew rate of the TL061IJG given by the manufacturer is 0.25 mA, while the minimum slew rate is 2 V/us. Its minimum voltage gain is 4000. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the TL061IJG gain becomes 0.707 times the low-frequency gain is 1000 kHz.

The nominal supply voltage of TL061IJG is 15 V, and its corresponding nominal negative supply voltage is -15 V. The power supply range is: +-15 V. The input offset voltage of TL061IJG is 9000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of TL061IJG:

The width of TL061IJG is: 7.62 mm and the length is 9.6 mm. TL061IJG has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm. Total pins: 8

TL061IJG amplifier other information:

TL061IJG adopts the VOLTAGE-FEEDBACK architecture. It belongs to the low-bias class of amplifiers. It does not belong to the low offset class of amplifiers. The frequency compensation status of TL061IJG is: YES. Its temperature grade is: INDUSTRIAL.

TL061IJG is not Rohs certified. The corresponding JESD-30 code is: R-GDIP-T8. The packaging code of TL061IJG is: DIP. The materials used in the TL061IJG package are mostly CERAMIC and GLASS-SEALED. The package shape is RECTANGULAR.

The TL061IJG package pin format is: IN-LINE. Its terminal form is: THROUGH-HOLE. The maximum seat height is 5.08 mm.

Recommended Resources

Fuse protection circuit one a

Use PSSR to make a gradual brightening and dimming light switch

LM386N-4 LM386 power amplifier circuit diagram

Use module KTM03 to control the power regulator circuit

Collector tuned oscillation circuit

Power carrier amplifier circuit

Smoke sensor as wireless power supply: Smoke sensor as wireless power design, hope the masters can give the best design solution Looking forward, it seems that there is a solution given by netizens I haven't tried it. There are only posts on Baidu such as "How to make a wireless in...; 蜀禅文化 Security Electronics

CH224 Circuit Design: The CH224 is so easy to use (this is really worth praising). After doing the initial test, I felt that there was nothing to test, so I started to draw the circuit directly. This time I plan to use the CH224 for another DIY programmable meter to get ...; dcexpert Domestic Chip Exchange

[STM32H7R/S] Review ⑤X-NUCLEO-IKS4A1 MEMS sensor transplantation: This article is a preliminary preparation for playing with NanoEdge AI Studio. This software is a software that allows users to train models by themselves, and can implement anomaly detection, outlier detection, classification, and regression lib...; 不爱胡萝卜的仓鼠 stm32/stm8

[MYD-JX8MMA7 development board based on ARM+FPGA architecture] BUG feedback - HDMI often has no output problem: Phenomenon: There is often a problem of no HDMI output after power failure and restart. The general process when a problem occurs is as follows: Power on - normal operation - power off - power on again - no HDMI output. Except for the HDMI ...; qinyunti Industrial Control Electronics

Multi-channel LED driver: Attached is the specification of the step-down constant current chip used to drive LEDs. I want to use this chip to drive multiple LEDs, such as four RGBW channels. I thought of a way to use four MOS tubes to cut the output, so that four outputs...; cpfpost Power technology

ADI's precision capacitance measurement solution sharing: Project topic: ADI's precision capacitance measurement solution Design background: In product design, it is necessary to dynamically collect weak capacitance values (pF level) and feed the capacitance values back to the microcontroller for correspo...; beyond_笑谈 ADI ·Excelpoint industrial technology

TL061IJG Also View