TLC081CDGNR datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> TLC081CDGNR

TLC081CDGNR: Part NumberTLC081CDGNR; CategoryAnalog mixed-signal IC Amplifier circuit; File Size28121.5，54 Pages; ManufacturerRochester Electronics; Websitehttps://www.rocelec.com/; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
TLC081CDGNR	Texas Instruments	Single Wide Bandwidth High Output Drive Single Supply Op Amp 8-MSOP-PowerPAD 0 to 70
TLC081CDGN	Rochester Electronics LLC	Basic information of TLC081CDGN amplifier:TLC081CDGN is an OPERATIONAL AMPLIFIER. Commonly used pack...
TLC081CDGNRG4	Texas Instruments	Operational Amplifiers - Op Amps Single Wide Bandwdth Hi-Output Sngl Sply
TLC081CDGNG4	Texas Instruments	Operational Amplifiers - Op Amps Single Wide Bandwdth Hi-Output Sngl Sply
TLC081IDGNR	Texas Instruments	Single Wide Bandwidth High Output Drive Single Supply Op Amp 8-MSOP-PowerPAD -40 to 125
TLC081IDGNRG4	Texas Instruments	Operational Amplifiers - Op Amps Single Wide Bandwdth Hi-Output Sngl Sply
TLC081IDGN	Texas Instruments	OP-AMP, 3000uV OFFSET-MAX, 10MHz BAND WIDTH, PDSO8, PLASTIC, MSOP-8

TLC081CDGNR Overview

Basic information of TLC081CDGNR amplifier:

TLC081CDGNR is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are GREEN, PLASTIC, MSOP-8

TLC081CDGNR amplifier core information:

The minimum operating temperature of the TLC081CDGNR is and the maximum operating temperature is 70 °C. Its peak reflow temperature is 260°C and its maximum average bias current is 0.0001 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the TLC081CDGNR has a nominal slew rate of 16 V/us. When the op amp is used in a closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the TLC081CDGNR gain becomes 0.707 times the low-frequency gain is 10000 kHz.

The nominal supply voltage of the TLC081CDGNR is 5 V. The upper limit of its supply voltage is 17. The input offset voltage of VTLC081CDGNR is 3000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of TLC081CDGNR:

The width of TLC081CDGNR is: 3 mm, the length is 3 mm. TLC081CDGNR has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 0.65 mm. Total pins: 8

TLC081CDGNR amplifier additional information:

Its temperature grade is: COMMERCIAL. And its humidity sensitivity level is: 1. TLC081CDGNR is not Rohs certified. It does not contain lead. The corresponding JESD-30 code is: S-PDSO-G8.

The corresponding JESD-609 code is: e4. The packaging code of TLC081CDGNR is: HTSSOP. The materials used for TLC081CDGNR packaging are mostly PLASTIC/EPOXY. The package shape is SQUARE. TLC081CDGNR package pin forms are: SMALL OUTLINE, HEAT SINK/SLUG, THIN PROFILE, SHRINK PITCH.

Its terminal forms are: GULL WING. The maximum seat height is 1.07 mm.

Recommended Resources

Do you know about the miniature infrared receiver with sensitivity and noise suppression capabilities?

Thyristor cut-off delay circuit 6

Industrial four-way programmable controller drive circuit

C1160 heavy lathe electrical control circuit schematic circuit

Universal timing controller circuit

One-way motor proportional drive circuit

[Digi-Key Follow me Issue 1] Work submission - Thermometer and hygrometer and network clock (play Happy Birthday song when turned on): Work submission - Thermometer and hygrometer and network clock demonstration video Project Introduction Introduction: This project aims to use CircuitPython to develop a device with temperature and humidity detection and network cl...; walker2048 DigiKey Technology Zone

【Luckfox RV1103】3. Basic peripheral test-PWM (python): # 【Luckfox RV1103】3. Basic peripheral test-PWM (python) Reference tutorial: https://wiki.luckfox.com/zh/Luckfox-Pico/Luckfox-Pico-PWM Luckfox RV1103 pin diagram: 1. Device directory: In the /sys/class/pwm/ directory, each PWM device has a separate ...; FFD8 Domestic Chip Exchange

Basic Op Amp Configuration: 1.1 Op Amp Basics 　　Step 1: Connecting DC Power 　　Op amps must always be supplied with DC power, so it is best to configure these connections before adding any other circuit components. Figure 1 shows one possible power supply configuration on a s...; Aguilera Analogue and Mixed Signal

[Zhongwei fast charging voltage application kit] Evaluation report 4: QC fast charging protocol learning: Now that the environment is set up and the lights are on, it’s time to learn about fast charging. After a week of searching the Internet, I found that there are very few resources on PD, and I still don’t understand it, but I found that QC seems ...; flyaqiao Domestic Chip Exchange

Reliability Design of Electrically Driven Titanium Wire (SMA) (7) Contact Surface Design: 【Foreword】 Shape memory alloy (SMA), also known as morphological memory alloy and titanium-nickel memory alloy, is composed of Ti (titanium)-Ni (nickel) materials. It is a wire made through multiple processes, which we call titanium wire for short...; 272151979 Integrated technical exchanges

TLC081CDGNR Also View