TLC071CDGN datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> TLC071CDGN

TLC071CDGN: Part NumberTLC071CDGN; CategoryAnalog mixed-signal IC Amplifier circuit; File Size24123.42，54 Pages; ManufacturerRochester Electronics; Websitehttps://www.rocelec.com/; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
TLC071CDGNR	Texas Instruments	Single Wide-Bandwidth High-Output-Drive Op Amp 8-MSOP-PowerPAD 0 to 70
TLC071CDGNRG4	Texas Instruments	Operational Amplifiers - Op Amps Sngl Wide-Bandwidth Hi-Output-Drv Op Amp
TLC071CDGNG4	Texas Instruments	Operational Amplifiers - Op Amps Sngl Wide-Bandwidth Hi-Output-Drv Op Amp
TLC071IDGN	Rochester Electronics LLC	OP-AMP, 3000uV OFFSET-MAX, 10MHz BAND WIDTH, PDSO8, GREEN, PLASTIC, MSOP-8
TLC071IDGNR	Texas Instruments	Single Wide-Bandwidth High-Output-Drive Op Amp 8-MSOP-PowerPAD -40 to 125
TLC071IDGNG4	Texas Instruments	Operational Amplifiers - Op Amps Sngl Wide-Bandwidth Hi-Output-Drv Op Amp
TLC071IDGNRG4	Texas Instruments	Operational Amplifiers - Op Amps Sngl Wide-Bandwidth Hi-Output-Drv Op Amp

TLC071CDGN Overview

Basic information of TLC071CDGN amplifier:

TLC071CDGN is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are GREEN, PLASTIC, MSOP-8

TLC071CDGN amplifier core information:

The minimum operating temperature of TLC071CDGN is and the maximum operating temperature is 70 °C. Its peak reflow temperature is 260°C and its maximum average bias current is 0.0001 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of TLC071CDGN is 16 V/us. When the op amp is used in a closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the TLC071CDGN gain becomes 0.707 times the low-frequency gain is 10000 kHz.

The nominal supply voltage of the TLC071CDGN is 5 V. The upper limit of its supply voltage is 17. The input offset voltage of VTLC071CDGN is 3000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of TLC071CDGN:

The width of TLC071CDGN is: 3 mm, the length is 3 mm. TLC071CDGN has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 0.65 mm. Total pins: 8

TLC071CDGN amplifier additional information:

Its temperature grade is: COMMERCIAL. And its humidity sensitivity level is: 1. TLC071CDGN is not Rohs certified. It does not contain lead. The corresponding JESD-30 code is: S-PDSO-G8.

The corresponding JESD-609 code is: e4. The packaging code of TLC071CDGN is: HTSSOP. The materials used for TLC071CDGN packaging are mostly PLASTIC/EPOXY. The package shape is SQUARE. TLC071CDGN package pin forms are: SMALL OUTLINE, HEAT SINK/SLUG, THIN PROFILE, SHRINK PITCH.

Its terminal forms are: GULL WING. The maximum seat height is 1.07 mm.

Recommended Resources

How many power supply methods are there for Arduino? What is the power circuit like?

Synchronous delayed dual clock circuit

Seven-function wireless remote control receiving circuit

Resistor-capacitor oscillation circuit

Nickel Cadmium Battery Charger

Energy-saving three-phase asynchronous motor phase failure protection circuit

rockchip RK3226 Hardware Development Guide: 1 System Overview1.1 OverviewRK3326 is a high-performance quad-core processor chip that can be used in tablets and smart audio devices. RK3326 has built-in multiple powerful embedded hardware engines, providing excellent performance for high-end ...; qq7643066 Embedded System

[Good book to read together - "Hardware Design Guide: From Device Cognition to Mobile Phone Baseband Design"] - 05 Introduction to LDO: Hardware Design Guide: From Device Knowledge to Mobile Baseband Design ——Introduction to Linear Regulated Power Supply LDO In daily circuit design, engineers often use linear regulators (LDOs) to power loads with low power noise requir...; zyb329321151 Switching Power Supply Study Group

Advanced Motor Control - PID Speed Control: The previous articles (Basics of Motor Control) introduced the principles of motor encoders, timer output PWM, timer encoder mode speed measurement, etc. Based on the previous articles, this article continues to learn motor control, uses the PID alg...; DDZZ669 Motor Drive Control（Motor Control）

[MM32 eMiniBoard Review] Part 7: IIC Read and Write EEPROM: 1. Introduction I saw in the introduction that it has 2Kbit of EEPROM, which means 256 bytes of storage space, and uses IIC communication, so let's give it a try. 2. Analysis Open the relevant routine, the path is as follows You can see t...; w494143467 Domestic Chip Exchange

What are switch quantity and analog quantity?: 　　What are switching quantity and analog quantity? People who are new to the industrial control industry may not be very clear. Let's first talk about what switching quantity and analog quantity are. What are their functions and what are the differe...; zhongs1 Analog electronics

【Follow me Season 2 Episode 2】+Project Summary: All tasks in the article are realized by the materials in the picture BOM: Manufacturer Manufacturer Part Number name Digi-Key Links Arduino ABX00087 Arduino UNO R4 WiFi https://www.digikey.cn/zh/products/det...; superw DigiKey Technology Zone

TLC071CDGN Also View