LT1816IDD#PBF datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> LT1816IDD#PBF

LT1816IDD#PBF: Part NumberLT1816IDD#PBF; CategoryAnalog mixed-signal IC Amplifier circuit; File Size5397.81，20 Pages; ManufacturerADI; Websitehttps://www.analog.com; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

LT1816IDD#PBF Overview

Basic information of LT1816IDD#PBF amplifier:

LT1816IDD#PBF is a high-speed operational amplifier (Op Amps - High Speed Operational Amplifiers) from Analog Devices Inc. It belongs to the LT1816 series of products.

LT1816IDD#PBF amplifier core information:

The minimum operating temperature of LT1816IDD#PBF is - 40 C and the maximum operating temperature is + 85 C. The corresponding working power supply current is 6.5 mA. The output current of each channel is: 80 mA.

The LT1816IDD#PBF has a power supply rejection ratio of 97 dB. (Power supply rejection ratio (PSRR): An indicator used to determine the impact of the amplifier output on the power supply. PSRR = 20log[(Ripple(in) / Ripple(out))], that is, the larger the value, the less the amplifier output is affected by the power input. The smaller.) The amplifier gain of LT1816IDD#PBF can reach: 3 V/mV (The amplifier gain is the logarithm of the ratio of the amplifier output power to the input power, which is used to indicate the degree of power amplification. It also refers to the amplification factor of voltage or current. Similarly , decibel is the unit of amplifier gain.) The gain bandwidth product (GBP, gain bandwidth product) of LT1816IDD#PBF is 220 MHz. As a parameter to simply measure the performance of the amplifier, if you are not sure how to choose your amplifier, you can This is a relatively simple measurement indicator. The corresponding input voltage noise density is 6 nV/rtHz and the corresponding input noise current density is 1.3 pA/rtHz.

When a voltage difference of 0.2 mV is input between the LT1816IDD#PBF input pins, the output voltage of this amplifier is 0V. (That is, its input bias voltage is 0.2 mV)

Related dimensions of LT1816IDD#PBF:

Number of channels in total: 2 Channels.

LT1816IDD#PBF amplifier additional information:

And its more detailed single package form is: DFN-8. When suppliers on the market sell LT1816IDD#PBF, they use the form: Tube.

Recommended Resources

High current (4A) switching regulator integrated circuit L296 outputs 5.1 to 40V

One of the thyristor answering circuits

Complete set of car radio equipment audio power amplifier 01

LM3578A is used as a +5V, -15V DC, DC converter circuit diagram

MC145026～MC145030 pin function diagram

MP3 circuit diagram 6

Anxinke PB-02 module evaluation (2) --- PHY62XX architecture introduction && design task introduction: Anxinke PB-02 module evaluation (2) --- PHY62XX architecture introduction && design task introduction This article was first published on EEWORLD. For details, please visit: EEWORLD Review PHY6212 Chip Introduction The PB-02 from Essence ...; jszszzy RF/Wirelessly

High drive chip channel output current problem: As shown in the picture, this is part of the manual information of the high-drive chip BTS7020-2EPA The maximum channel load current IL mentioned in Figure 1 can be obtained through the table relationship in Figure 2. Does Figure 2 look like this:...; shaorc Analog electronics

The 4056 charging chip has two status output pins STDBY and CHRG: The 4056 charging chip has two status output pins STDBY and CHRG When the LED indication is not connected, these two pins can be used as the status output pins of the charging chip to give the current status to the MCU for judgment, such as charg...; QWE4562009 Test/Measurement

[Xianji HPM6750 Review] Running the Edge AI Framework - TFLM Benchmark: This article will introduce what TFLM is, then introduce the official TFLM benchmark, and how to run the TFLM benchmark on the HPM6750 and compare it with the benchmark results on the Raspberry Pi 3B+. What is TFLM? You may have heard of Tens...; xusiwei1236 Domestic Chip Exchange

[The 3rd Xuantie Cup RISC-V Application Innovation Competition] LicheePi 4A+ initial environment familiarity: After receiving the LicheePi 4A development board, I had mixed feelings and excitement. As a developer, I am always curious and looking forward to new hardware platforms. However, the debugging process was not easy. First, I encountered some power s...; yinxx XuanTie RISC-V Activity Zone

Temperature compensated crystal oscillator is also a kind of quartz crystal oscillator, referred to as "temperature compensated crystal oscillator": What are the characteristics of temperature compensated crystal oscillators? Because the requirements of electronic products in different fields for quartz crystal oscillators are different, and temperature compensated crystal oscillators are devel...; YXC扬兴晶振 Discrete Device

LT1816IDD#PBF Also View