RC4227FN datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> RC4227FN

RC4227FN: Part NumberRC4227FN; CategoryAnalog mixed-signal IC Amplifier circuit; File Size4474.73，9 Pages; ManufacturerRaytheon Company; Websitehttps://www.raytheon.com/

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

RC4227FN Overview

Basic information of RC4227FN amplifier:

RC4227FN is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are DIP, DIP8,.3

RC4227FN amplifier core information:

The minimum operating temperature of RC4227FN is and the maximum operating temperature is 70 °C. Its peak reflow temperature is NOT SPECIFIED Its maximum bias current at 25°C is: 0.015 µA Its maximum average bias current is 0.015 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the RC4227FN has a nominal slew rate of 2.7 V/us. The minimum slew rate of RC4227FN given by the manufacturer is 1.5 V/us. Its minimum voltage gain is 400000. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the RC4227FN gain becomes 0.707 times the low-frequency gain is 8000 kHz.

The nominal supply voltage of RC4227FN is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of RC4227FN is 75 µV (Input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of RC4227FN:

RC4227FN has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm.

RC4227FN amplifier additional information:

RC4227FN adopts the VOLTAGE-FEEDBACK architecture. It belongs to the low offset class of amplifiers. The frequency compensation status of RC4227FN is: YES. Its temperature grade is: COMMERCIAL. RC4227FN is not Rohs certified.

The corresponding JESD-30 code is: R-PDIP-T8. The corresponding JESD-609 code is: e0. The packaging code of RC4227FN is: DIP. RC4227FN packaging materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR.

The RC4227FN package pin format is: IN-LINE. Its terminal form is: THROUGH-HOLE.

Recommended Resources

Audio dial encoder

STK4162 II power amplifier circuit diagram

Two practical password controller circuits b

JFET crystal oscillator circuit diagram

Traffic light control circuit diagram

Sub-ultrasonic remote control switch circuit

HEF4051 is a substitute for which commonly used chip? I want to see the application data of commonly used chips with the same function.: HEF4051 is a substitute for which commonly used chip? There is too little application information for this chip. I want to see the application information of commonly used chips with the same function. Thank you. CD4051. If you use a power suppl...; 深圳小花 PCB Design

IAP issue when porting from Qinheng CH32F103 to CH32V103: When porting from CH32F103 to CH32V103, the original program has IAP. After switching to RISC-V, I don't know how to convert the instructions. The main questions are: 1. In the ld file, the ROM start address is 0x00000000. Can it be changed to 0...; 火辣西米秀 Domestic Chip Exchange

I have posted a post about 1588BS dot matrix before. This is the follow-up, which is about 51 single chip microcomputer.: It's like this. I used a multimeter to test the 1588bs dot matrix I soldered on the board and found that it was functioning properly. Then I soldered the 74HC595 chip and tested the dot matrix. It was functioning properly. Later, I soldered the s...; 示范法 stm32/stm8

Newly defined key evaluation suite - Source insight import: Since I installed keil4, I couldn't use the EIDE plug-in of vscode to import the C51 project. I found that I could use sourceinsight to complete the C51 project migration, which is also very good to use. Source insight main page New Project ...; 小屋22 Domestic Chip Exchange

Please tell me the difference between MPU6500/6050/6000: What are the specific differences between MPU6500/6050/6000? There is a specific comparison on the official website. ...; sky999 PCB Design

[Yichuang ET6001 Review] Control LED with KEY: For the input function of a GPIO port, a touch button is specially configured for it to control the on and off of the LED. Among them, GPIO2_4 is connected to LED9 on the development board; GPIO2_3 is connected to the output pin of the touch butto...; jinglixixi Domestic Chip Exchange

RC4227FN Also View