EL5227CR-T7 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> EL5227CR-T7

EL5227CR-T7: Part NumberEL5227CR-T7; CategoryAnalog mixed-signal IC Amplifier circuit; File Size7878.93，17 Pages; ManufacturerRenesas Electronics Corporation; Websitehttps://www.renesas.com/

Alternative parts

Part Number	Manufacturer	Description
EL5227CRZ	Renesas Electronics Corporation	Basic information of EL5227CRZ amplifier:EL5227CRZ is a BUFFER from Intersil. Commonly used packagin...
EL5227CRZ-T13	Renesas Electronics Corporation	Operational Amplifiers - Op Amps EL5227CRZ OCTALUFR LW PWR
EL5227CRZ-T7	Renesas Electronics Corporation	Operational Amplifiers - Op Amps EL5227CRZ OCTALUFR LW PWR
EL5227CR-T13	Renesas Electronics Corporation	IC OPAMP BUFFER 2.5MHZ 20TSSOP
EL5227CR	Elantec	Buffer Amplifier,

EL5227CR-T7 Overview

Basic information of EL5227CR-T7 amplifier:

EL5227CR-T7 is a BUFFER. The commonly used packaging method is TSSOP-20

EL5227CR-T7 amplifier core information:

The minimum operating temperature of EL5227CR-T7 is -40 °C and the maximum operating temperature is 85 °C. Its peak reflow temperature is 2400°C. Its maximum bias current at 25°C is: 0.05 µA. Its maximum average bias current is 0.05 µA.

How to simply check the efficiency of an amplifier? Looking at its slew rate, the EL5227CR-T7 has a nominal slew rate of 2.2 V/us. The maximum slew rate of the EL5227CR-T7 given by the manufacturer is 1.55 mA, while the minimum slew rate is 0.9 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the EL5227CR-T7 gain becomes 0.707 times the low-frequency gain is 2.5 MHz.

The nominal supply voltage of EL5227CR-T7 is 5 V, and its corresponding nominal negative supply voltage is -5 V. The input offset voltage of EL5227CR-T7 is 15000 µV (input offset voltage: the compensation voltage required between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of EL5227CR-T7:

The width of EL5227CR-T7 is: 4.4 mm and the length is 6.5 mm. EL5227CR-T7 has 20 terminals. Its terminal position type is: DUAL. Terminal pitch is 0.65 mm. Total pins: 20

EL5227CR-T7 amplifier additional information:

Its temperature grade is: INDUSTRIAL. And its humidity sensitivity level is: 1. EL5227CR-T7 is not Rohs certified. The corresponding JESD-30 code is: R-PDSO-G20. The corresponding JESD-609 code is: e0.

The packaging code of EL5227CR-T7 is: SOP. EL5227CR-T7 packaging materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The EL5227CR-T7 package pin format is: SMALL OUTLINE. Its terminal forms are: GULL WING.

The maximum seat height is 1.2 mm.

Recommended Resources

Use TL431 to make a simple charger circuit

Serial input 12-bit DA conversion interface circuit

Three-phase active power meter, power factor meter, ammeter and commutation switch connection

Timing loop music performance circuit

Two-speed motor control circuit

Pyroelectric detection and radio transmission circuit

[Digi-Key Follow me Issue 4] + Task Summary and Supplement: ## Supplement: Submit tasks and videos# Content 1: Demonstration video Summarize the videos of each task: # Content 2: Summary of tasks### W5500-EVB-Pico|Unboxing Post (https://en.eeworld.com/bbs/thread-1269950-1-1.html "Unboxing Post") ### W5...; alanlan86 DigiKey Technology Zone

Simple inverter circuit: From: https://www.hackster.io/dhritimanhb2015 ... uit-21e30b This is a simple inverter circuit based on 13007 transistor, which is very suitable for small loads such as 15w LED bulbs, mobile chargers and other devices. After supplying 12V to t...; dcexpert DIY/Open Source Hardware

MCU+MOS tube stepping subdivision drive control solution: Everyone, I have been using Toshiba's integrated chips, but now I find that the currents are all small, not large. I can only use discrete components to build large currents myself. I saw an introduction that said I can use the MCU+MOS tube solution...; luospring Motor Drive Control（Motor Control）

Does the battery in the KVASER Memorator Professional analyzer need to be replaced?: Does the battery in the KVASER Memorator Professional analyzer need to be replaced? KVASER Memorator Professional can draw power from the USB port or external power supply, with an independent working voltage of 7V-36V and a power consumption of o...; 是广州智维的段工呀 Automotive Electronics

【BIGTREETECH PI Development Board】System Burning and First Experience: Preface The first step to play with the computer is to install the system, then familiarize yourself with the basic configuration of the board, networking, SSH login, etc., and familiarize yourself with the basic system environment and operations....; qinyunti Domestic Chip Exchange

Have you heard?: Well done, I hope the environment will get better and better! I've heard that... I'm looking forward to it getting better and better... It’s great that the desert has been controlled. This is a great achievement that will benefit futu...; okhxyyo Power technology

EL5227CR-T7 Also View