5962-8954303PX datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> 5962-8954303PX

5962-8954303PX: Part Number5962-8954303PX; CategoryAnalog mixed-signal IC Amplifier circuit; File Size1550.35，10 Pages; ManufacturerADI; Websitehttps://www.analog.com

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

5962-8954303PX Overview

5962-8954303PX amplifier basic information:

5962-8954303PX is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are CERAMIC, DIP-8

5962-8954303PX amplifier core information:

The minimum operating temperature of the 5962-8954303PX is -55 °C and the maximum operating temperature is 125 °C. Its peak reflow temperature is NOT SPECIFIED Its maximum average bias current is 0.0002 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the 5962-8954303PX has a nominal slew rate of 9 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the 5962-8954303PX gain becomes 0.707 times the low-frequency gain is 3000 kHz.

The nominal supply voltage of 5962-8954303PX is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of 5962-8954303PX is 3000 µV (Input offset voltage: the compensation voltage between the two input terminals required to make the output terminal of the operational amplifier 0V (or close to 0V).) The width of 5962-8954303PX is: 7.62 mm .

Related dimensions of 5962-8954303PX:

5962-8954303PX has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm. Total pins: 8

5962-8954303PX amplifier additional information:

Its temperature grade is: MILITARY. 5962-8954303PX is not Rohs certified. The corresponding JESD-30 code is: R-CDIP-T8. The packaging code of 5962-8954303PX is: DIP. The materials of 5962-8954303PX package are mostly CERAMIC, METAL-SEALED COFIRED.

The package shape is RECTANGULAR. The pin format of 5962-8954303PX package is: IN-LINE. Its terminal form is: THROUGH-HOLE. The maximum seat height is 5.08 mm.

Recommended Resources

LTM8045 SEPIC regulator application circuit diagram collection

Control circuit with multiple buttons to start and stop a motor

Huayi brand advanced reciprocating electric shaver circuit diagram

Voltage doubling conversion circuit diagram 2

4-digit LCD display and 8031 interface circuit

Voltage relay protection circuit for neutral point voltage phase loss

Basic knowledge of battery charging IC circuit design: Charging a battery is simple (in theory) - apply a voltage between the terminals and the battery charges. If safe charging, fast charging, and/or maximum battery life are important, then things get complicated. This article will consider various ...; qwqwqw2088 Power technology

Newcomer Report: Newcomer report, thank you for your support Welcome, welcome, warm welcome, welcome, welcome, warm welcome, welcome, welcome, warm welcome, It looks like another advertisement~ ...; 热心市民s Mobile and portable

FAQ_How to determine the phase of the output PWM signal in BlueNRG-12: Author: Weisheng CHEN, ST engineer Click to download the pdf document to view: Keywords: BlueNRG-1/2, PWM, waveform flipping Question: When using the MFT module in BlueNRG-1/2 to output a PWM signal, how is its initial phase determined? B...; nmg ST - Low Power RF

Temperature detection [What is the device sensor you are most comfortable using]?: 【Let’s talk about temperature detection and application】 1. rice cooker Water Heater Water boiler Water dispenser 2. High and low temperature test chamber Electric soldering i...; btty038 Integrated technical exchanges

Boost DCDC for constant current LED driving, inductor heating problem: The chip is XL6006. According to the typical application circuit design, we want to boost 24V to 36V, output current 1A, load current more than 900mA. After the circuit design is completed, the inductor heats up quite a lot. The inductor rating i...; S3S4S5S6 LED Zone

Rockchip RV1126 reads USB camera: Help: When using rv1126 to read a USB camera, using opencv or directly pulling the camera image from the application layer, and then displaying it on the Qt interface, the video image presented is incomplete, or after pulling the image, it is direct...; liuuuuuuuuuu Embedded System

5962-8954303PX Also View