DSC6342JE3HB-001.0000T datasheet, PDF

DSC6342JE3HB-001.0000T: DescriptionLVCMOS Output Clock Oscillator, 1MHz Nom; CategoryPassive components oscillator; ManufacturerMicrochip; Websitehttps://www.microchip.com

Download Datasheet Parametric View All

DSC6342JE3HB-001.0000T Overview

LVCMOS Output Clock Oscillator, 1MHz Nom

Parameter Name	Attribute value
Objectid	7271638847
Reach Compliance Code	compliant
Country Of Origin	Thailand
YTEOL	6.44
Other features	AEC-Q100; ENABLE/DISABLE FUNCTION; TR
maximum descent time	1.5 ns
Frequency Adjustment - Mechanical	NO
frequency stability	20%
Installation features	SURFACE MOUNT
Number of terminals	4
Nominal operating frequency	1 MHz
Maximum operating temperature	70 °C
Minimum operating temperature	-20 °C
Oscillator type	CMOS
Output load	15 pF
physical size	2.5mm x 2.0mm x 0.89mm
longest rise time	1.5 ns
Maximum supply voltage	3.63 V
Minimum supply voltage	1.71 V
surface mount	YES
maximum symmetry	55/45 %

[Transfer] Basic knowledge of electronic components - inductor: An inductor coil is a coil of wire wound around an insulating tube. The wires are insulated from each other, and the insulating tube can be hollow or contain an iron core or a magnetic powder core, re...; 赵玉田 Analog electronics

IIC deadlock problem solution: During the stress test of a microwave product, it was found that the single board was hung during startup, and the version could not be successfully powered on after the timeout reset, and the problem...; 鬼谷清泉 MCU

I would like to ask how high frequency sine waves are generated.: Can anyone tell me, thank you in advance!!...; firstlong Analog electronics

Analysis and Design of TL431 Feedback Loop: TL431 (as shown in Figure 1) is one of the most commonly used three-terminal adjustable current reference sources. It has good thermal stability and high cost performance. It is widely used in op amp ...; qwqwqw2088 Analogue and Mixed Signal

How to connect stepper motor: I want to write a code to control a stepper motor and let it rotate 10,000 times, but I was completely confused when I got the motor. There are six pins: GND, A+, A-, B+, B-, and VCC. 1. If the pulse ...; 刘123 Motor Drive Control（Motor Control）

Question: What is the resistance and capacitance coordination problem for anti-interference of grounding circuit?: If the output of the bridge is left floating, there will be a common mode voltage problem, so the output is connected to the ground through a large resistor, and a capacitor is connected to the resist...; leslie Analog electronics

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components