EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

GUS-SS4B-00-1521-DC

Description
Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.05W, 1520ohm, 100V, 0.5% +/-Tol, -250,250ppm/Cel, 1915,
CategoryPassive components    The resistor   
File Size277KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUS-SS4B-00-1521-DC Overview

Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.05W, 1520ohm, 100V, 0.5% +/-Tol, -250,250ppm/Cel, 1915,

GUS-SS4B-00-1521-DC Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid798609974
package instructionSMT, 1915
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL5.63
structureMiniature
JESD-609 codee0
Network TypeBussed
Number of terminals8
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height1.626 mm
Package length4.902 mm
Package formSMT
Package width3.886 mm
method of packingTR
Rated power dissipation(P)0.05 W
resistance1520 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesSOIC
size code1915
technologyTANTALUM NITRIDE/NICKEL CHROME
Temperature Coefficient250 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Tolerance0.5%
Operating Voltage100 V
【DIY Creative LED】Add touch button and install it on LED lamp
[i=s]This post was last edited by dcexpert on 2020-10-3 17:59[/i]The effect after installing the touch spring and fixing it with hot melt glue. When applying glue, use a USB cable to assist to avoid a...
dcexpert MCU
Know a little about the AD sampling single mode of dsp28335
Three modes are configured: single mode, continuous mode and DMA transfer. Single mode calls the acquisition function once to collect data at a specified AD port, and samples when needed. Continuous m...
fish001 DSP and ARM Processors
[RISC-V MCU CH32V103 Review] - 2: Making an LED flash is not easy
[i=s]This post was last edited by MianQi on 2021-1-28 11:56[/i]Let's look at the wiring first (the tutorial says to directly connect PinA0\PinA1 and LED1\LED2 with jumpers. I'm not used to doing this,...
MianQi Domestic Chip Exchange
SensorTile.box uses air pressure sensors to analyze environmental changes
After the SensorTile.box is flashed with DataLogExtended firmware, the sensor output data waveform can be directly viewed using Unicleo-GUI The following is the data obtained by using the air pressure...
littleshrimp MEMS sensors
Integrated circuit detection method
Editor's note: Although there are ways to replace integrated circuits, disassembly is troublesome after all. Therefore, before disassembly, you should accurately determine whether the integrated circu...
fighting Test/Measurement
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号