EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

CRA06E0803302JRT6E3

Description
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 3000ohm, 50V, 5% +/-Tol, -200,200ppm/Cel, 1206,
CategoryPassive components    The resistor   
File Size126KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

CRA06E0803302JRT6E3 Overview

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 3000ohm, 50V, 5% +/-Tol, -200,200ppm/Cel, 1206,

CRA06E0803302JRT6E3 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid968512541
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
JESD-609 codee3
Network TypeIsolated
Number of terminals8
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length3.2 mm
Package formSMT
Package width1.5 mm
method of packingTR, Paper, 13 Inch
Rated power dissipation(P)0.063 W
resistance3000 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCRA06E
size code1206
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient-200,200 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Tolerance5%
Operating Voltage50 V
Can anyone give me a serial port interrupt receiving program for STM32F03 without HAL library?
Can anyone give me a non-HAL library STM32F03 serial interrupt receiving program? Self-written or old program library is fine....
bigbat stm32/stm8
MAXIM was finally acquired
According to ADI news (https://www.analog.com/en/about-adi/news-room/press-releases/2021/8-26-21-adi-completes-acquisition-of-maxim-integrated.html), ADI has completed the acquisition of Maxim Integra...
dcexpert Talking
AD9 won't work anymore
The rules do not allow short circuits. I don't know why the wire can be pulled even though it is smaller than the gap, resulting in a direct short circuit. The original setup either pushed the existin...
呜呼哀哉 Analog electronics
Xunwei-i.MX6 development board manual update-non-device tree uboot-modify default environment variables
This document mainly introduces how to modify the default boot parameters of non-device tree uboot. After the iTOP-iMX6 development board is burned, the default is the system parameters and screen par...
遥寄山川 ARM Technology
How to solve the signal fluctuation from the sensor?
The signal from the sensor is very weak, and the circuit behind it has been amplified and filtered. When the detection quantity remains unchanged, the amplified signal has certain fluctuations. Lookin...
sfcsdc Analog electronics
TMS320C6678 power-on configuration
1. What is the DSP power-on reset configuration? The DSP big-endian, little-endian, self-starting (boot) mode, PCIe mode, and network coprocessor clock selection need to be selected at power-on reset....
Jacktang DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号