EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

501876-3214

Description
Board Connector, 32 Contact(s), 2 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Locking
CategoryThe connector    The connector   
File Size77KB,1 Pages
ManufacturerMolex
Websitehttps://www.molex.com/molex/home
Download Datasheet Parametric View All

501876-3214 Overview

Board Connector, 32 Contact(s), 2 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Locking

501876-3214 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknow
body width0.327 inch
subject depth0.57 inch
body length1.339 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedTIN OVER NICKEL
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Durability30 Cycles
Insulation resistance1000000000 Ω
insulator materialGLASS FILLED NYLON
Manufacturer's serial number501876
Plug contact pitch0.079 inch
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.0066 mm
polarization keyPOLARIZED HOUSING
Rated current (signal)2 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.126 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts32
Base Number Matches1
AD drawing PCB has many white lines after enlarging
When the AD PCB is enlarged, there are many white lines, not flying lines, and many horizontal bars. If it is not enlarged, there are only flying lines. Please help, what is going on?...
你的虎牙脆 PCB Design
AD Ignore DRC with irregular slotting settings using pad stacking
[i=s]This post was last edited by p0we7 on 2019-7-30 22:44[/i]======================= Solved: It turned out that the Hold to Hold rule did not have online detection enabled, so the corresponding DRC w...
p0we7 PCB Design
High frequency characteristics of resistors
High frequency characteristics of resistorsWhen resistors are used in high-frequency applications, the effects of the resistor's inherent inductance and inherent capacitance must be considered. At thi...
btty038 RF/Wirelessly
Problems with dynamic load line locus of transistor switches
[i=s]This post was last edited by engineer-x on 2022-2-9 17:36[/i]In the chapter on transistor switching principles in the power supply book, The book says that when an inductive load is connected, th...
engineer-x Analog electronics
Power supply solutions in the design of mobile communication terminal equipment
Power supply solutions in the design of mobile communication terminal equipment...
gaoyanmei Power technology
Choose a few diodes to learn more about
[align=left][font=微软雅黑]Diode is one of the most commonly used electronic components. Its biggest characteristic is unidirectional conductivity, that is, current can only flow through one direction of ...
youganw Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号