EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

RC0402FR-0725R5L

Description
Resistance (ohms): 25.5 Accuracy: ±1% Power: 1/16W Temperature coefficient: ±100ppm/°C
CategoryPassive components    The resistor   
File Size826KB,10 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

RC0402FR-0725R5L Online Shopping

Suppliers Part Number Price MOQ In stock  
RC0402FR-0725R5L - - View Buy Now

RC0402FR-0725R5L Overview

Resistance (ohms): 25.5 Accuracy: ±1% Power: 1/16W Temperature coefficient: ±100ppm/°C

RC0402FR-0725R5L Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionSMT, 0402
Reach Compliance Codecompliant
ECCN codeEAR99
structureRectangular
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.35 mm
Package length1 mm
Package formSMT
Package width0.5 mm
method of packingTR, Paper, 7 Inch
Rated power dissipation(P)0.0625 W
Rated temperature70 °C
resistance25.5 Ω
Resistor typeFIXED RESISTOR
size code0402
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage50 V
Base Number Matches1
【DIY Creative LED】Add touch button and install it on LED lamp
[i=s]This post was last edited by dcexpert on 2020-10-3 17:59[/i]The effect after installing the touch spring and fixing it with hot melt glue. When applying glue, use a USB cable to assist to avoid a...
dcexpert MCU
Know a little about the AD sampling single mode of dsp28335
Three modes are configured: single mode, continuous mode and DMA transfer. Single mode calls the acquisition function once to collect data at a specified AD port, and samples when needed. Continuous m...
fish001 DSP and ARM Processors
[RISC-V MCU CH32V103 Review] - 2: Making an LED flash is not easy
[i=s]This post was last edited by MianQi on 2021-1-28 11:56[/i]Let's look at the wiring first (the tutorial says to directly connect PinA0\PinA1 and LED1\LED2 with jumpers. I'm not used to doing this,...
MianQi Domestic Chip Exchange
SensorTile.box uses air pressure sensors to analyze environmental changes
After the SensorTile.box is flashed with DataLogExtended firmware, the sensor output data waveform can be directly viewed using Unicleo-GUI The following is the data obtained by using the air pressure...
littleshrimp MEMS sensors
Integrated circuit detection method
Editor's note: Although there are ways to replace integrated circuits, disassembly is troublesome after all. Therefore, before disassembly, you should accurately determine whether the integrated circu...
fighting Test/Measurement
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号