-1-
产 品 规 格 书
PRODUCT SPECIFICATION
SIRLES
MODEL
1.RATING
2.CONSTRUTION DIMENSION
结构尺寸
3.APPEARANCE
外观
4.CONTACTLOOP
接触回路
ITEM
专案
5.CAPABILITY OF ELECTRIC电气性½
5A
INSULATION RESISTANCE
绝缘电阻
Measurements shall be made following Application
of DC500V potential across terminals and across 100
MΩ
min
terminals and fuame for 1minute,
在端子之间和端
100
兆欧以上.
子与壳之间加
DC500V
条件下,持续
1
分钟测量.
AC250V、50HZ、1
min(imin(interrupting
There shall be no
current
≤500uA).
AC250V、50HZ、1
分钟(漏
briakdown
无击穿
电流
500uA)
现象出现。
Addition 1.5-2 time force on the top of the keystrok 100
m
Max
Ω
m
Ω 以
and press the switch,DC50V100mA在按键顶端上
(100
等于½用力
1.5-2
倍的力按动开关,DC50V,10Ma.
下).
系列:FLIP
SWITCHES(½触开关)
型号:
TS6620CJ
额定值:50Ma
12VDC
Apply to the appended drawing:
合附加图纸
符
Have no remarkable damage,crack and rust etc:
无
明显损伤,裂纹,锈迹等.
Monople loop:
单通单极回路
TEST CONDITION
测试条件
SPECIFICATION
规格
5B
WITHSTAND VILTAGE
耐电压
5C
CONTACT CIRCUIT
接触电路
5D
Addition DC5V on the two side of switch,at a speed The flash time
SWITCH
CONNECTION of 3-5time a sec.to press the switch.
开关的两端
betwcen open not
在
FLASH
开关接触点抖动
加
DC5V
的电压,以
3-5
次/秒的速度按动开关.
more than 10ms.
开关在接通和断开
时的接点抖动时间
不大于
10 ms.
Switch
electric
The contact shall be capable of a rorce of 5N for 5 andmechanical
seconds in any directions.
开关动½方向可承受
efficiency
沿
does
静½压力
5N,保持 5
秒钟.
not break
无损开
关电气或者机械
性½
按键行程:0.3±0.1
Being measure at across spring piece and across Contact switch’sd
keystoke forergometer.
测力计在按键与弹片之
drive dirive fouce
用
间测量.
was260
±
30gf.
按
键的开关驱动力为
260
±30gf
1
6.MECHANICAL EFFICIENCY
机械性½
6A
CONTACT STRENGTH
按键强度
6B
6C
CONTACT JOURNEY
DRIVE FORCE
驱动力
-2-
产 品 规 格 书
PRODUCT SPECIFICATION
A force of 1N being appling in any directions of the Switch mechanical
switch connection partt..
接线端的½用方向½
efficiency does not
在
加
1N
的力.
break.无损开关机
械性½.
Operatin at a rate of 30-50 cycles a minute.
以
30-50
次/分的驱动速度操½.
The first temperature shall be 70℃
,3h and
changed to-25℃,0.5h,5cycles of above test.
先
70℃,3h,然后-25℃,0.5h,如此重复
5
次.
Lif
e:50000
ycles
寿½
50000
次
1. The appearance
should not break.外观
应无损伤.
2. Contact
resistance
≤
100 m
Ω
接触电阻≤100
mΩ
3.
Insulation
resistance
≥
100
M
Ω.
绝缘电阻≥100
MΩ
6D
CONNECTION
STRENGTH
接线端强度
MECHANICAL LIFE
机械寿½
6E
7.ENVIRONME
7A
NT----RESISTANT EFFICIENCY
耐环境性½
CHANGE OF
TEMPERATURE
温度变化
7B
40±2℃
in temperature and 90-95%RH,Ruring
thetest time without load; After testing
HUMIDITY RESISTANT
耐
湿
the temperature should be 24h.经
40±2℃,
热
相对湿度
90-95%,试验期间,开关不动½,不带
电负荷,试验后恢复到常温
24h.
8.IOINTING EFFICIENCY
焊接性½
8A
SOLDERABILITY
可焊性
Solderability part
Temperature240±5℃;Duration;3±0.5S:温度在 should above 90%
240±5℃,持续
3±0.5S.
可焊部分被焊料
覆盖面应在
90%
以上.
Froth height of assist
solder should under
board
and
switch
electric
and
mechanical efficien-
cy does not break.助焊
剂发泡不应超过印制
板,无损伤开关电气或
机械动½性½.
8B
SOLDER—RESISTANT
耐焊剂性
Warm-up temperature:100℃,40S,焊锡温度
230
±5
℃,浸焊时间
3±0.5S.
8C
JOINTING—RESISTANT
耐焊接热
NORMAL JOLNTING TIMES
正常焊接次数
Jointing temperature: 240± 5
℃
,Duration of
efficiency does not
immersion: 5±1S.焊锡温度
240±5℃,浸焊时间 break
无损伤开关
5±1S
电气或机械动½性
½.
≤2times
小于
2
次
8D
9.NOTES
9A
The whole boxes of switch should keep in the temperature -30--80
and less than 80%RH withort
℃
acidic,alkalescence,caustic gas in the environment of the storage.
整箱包装的开关,应在温度为-30--80℃,相对湿度不大于
80%,周围的空气中没有酸性、碱性或其他腐蚀
性气½的库房内保管。
Operating Temperature Range:-20 to 70
℃
操½温度的范围:-20
to 70℃
Switch should install in a correct method.
开关应按正确的安装方法进行正确安装½用。
9B
9C
2