SP1-008-S137/02-99/2 datasheet, PDF

SP1-008-S137/02-99/2: DescriptionBoard Connector, 8 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle; CategoryThe connector The connector; File Size230KB，2 Pages; ManufacturerE-tec Interconnect Ltd.; Environmental Compliance

Download Datasheet Parametric View All

SP1-008-S137/02-99/2 Overview

Board Connector, 8 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	E-tec Interconnect Ltd.
Reach Compliance Code	compliant
body width	0.079 inch
subject depth	0.205 inch
body length	0.63 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	SN
Contact completed and terminated	Tin (Sn)
Contact point gender	MALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	20 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	500VAC V
Insulation resistance	1000000000 Ω
Insulator color	BLACK
insulator material	POLYBUTYLENE TEREPHTHALATE
JESD-609 code	e3
Manufacturer's serial number	SP1
Plug contact pitch	0.079 inch
Installation method	STRAIGHT
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Rated current (signal)	1 A
Guideline	UL
reliability	COMMERCIAL
Terminal length	0.224 inch
Terminal pitch	2.0066 mm
Termination type	SOLDER
Total number of contacts	8
Base Number Matches	1

How to avoid pitfalls in GPIO operations?: GPIO operation is the most basic operation when using a microcontroller. Even if you are not careful during this operation, you will still fall into a pit .For example: use two pins (PA00 and PA01) in...; 火辣西米秀 Domestic Chip Exchange

Mini2440 external interrupt programming: 1. Interrupt Writing General Block Diagram2. Step-by-step introduction 1. Initialize the pin #define GPGCON (*(volatile unsigned long *)0x56000060)Refer to the above figure and set all pins to [10] to...; 灞波儿奔 Microcontroller MCU

The bigger the resistor, the greater the noise? Not necessarily!: 1 Let’s look at the bad side first and review the resistor noise problem The noise of a resistor usually refers to thermal noise. Even if the resistor is not connected to the circuit and no current fl...; IIDA_Germinal PCB Design

Mobile car speed measurement: [i=s]This post was last edited by yachong001 on 2020-1-14 13:57[/i]A small car, driven by friction, has no wheels, and has a pole at the bottom. The track it walks on is distributed with different whe...; yachong001 Analog electronics

Study on the Amine Bond Technology of Carbon Membrane: Study on the Amine Bond Technology of Carbon Membrane...; lorant RF/Wirelessly

Install LSD-FET430UIF emulator driver: Due to project requirements, I needed to use 430. I had never used 430 before, so I started from scratch. The first thing to do is to install the emulator driver. I struggled with this problem for a l...; 灞波儿奔 Microcontroller MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components