EEWORLDEEWORLDEEWORLD

Part Number

Search
 

MAX473CPA+

Part NumberMAX473CPA+
CategoryAnalog mixed-signal IC    Amplifier circuit   
File Size11409.18,13 Pages
ManufacturerRochester Electronics
Websitehttps://www.rocelec.com/
Environmental Compliance  
Download Datasheet Parametric

Alternative parts

Part Number Manufacturer Description
MAX473CPA Rochester Electronics LLC Basic information of MAX473CPA amplifier:MAX473CPA is an OPERATIONAL AMPLIFIER. The commonly used pa...
MAX473EPA+ Rochester Electronics LLC MAX473EPA+ amplifier basic information:MAX473EPA+ is an OPERATIONAL AMPLIFIER. Commonly used packagi...
MAX473EPA Rochester Electronics LLC MAX473EPA amplifier basic information:MAX473EPA is an OPERATIONAL AMPLIFIER. The commonly used packa...
MAX473MJA Rochester Electronics LLC Basic information about MAX473MJA amplifier:MAX473MJA is an OPERATIONAL AMPLIFIER. The commonly used...

MAX473CPA+ Overview

Basic information about MAX473CPA+ amplifier:

MAX473CPA+ is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are 0.300 INCH, PLASTIC, DIP-8

MAX473CPA+ amplifier core information:

The minimum operating temperature of the MAX473CPA+ is 70 °C. Its peak reflow temperature is 260°C and its maximum average bias current is 0.175 µA

When the op amp is used in closed loop, at a specified closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the MAX473CPA+ gain becomes 0.707 times the low-frequency gain is 12000 kHz.

The nominal supply voltage of the MAX473CPA+ is 5 V. The upper limit of its supply voltage is 7 V. The input offset voltage of MAX473CPA+ is 2000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of MAX473CPA+:

The width of MAX473CPA+ is: 7.62 mm and the length is 9.375 mm. MAX473CPA+ has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm. Total pins: 8

MAX473CPA+ amplifier additional information:

Its temperature grade is: COMMERCIAL. And its humidity sensitivity level is: 1. MAX473CPA+ is not Rohs certified. It does not contain lead. The corresponding JESD-30 code is: R-PDIP-T8.

The corresponding JESD-609 code is: e3. The packaging code of MAX473CPA+ is: DIP. The materials used in the MAX473CPA+ package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The MAX473CPA+ package pin format is: IN-LINE.

Its terminal form is: THROUGH-HOLE. The maximum seat height is 4.572 mm.

Power System Stability and Control (3rd Edition)
This book is divided into three parts. The first part is power system protection, which introduces transformer protection, synchronous generator protection, transmission line protection, system protection, digital relay protection, using recorders t...
arui1999 Download Centre
IBIS model parameter modification
As shown in the figure, when using Allegro simulation, IBIS needs to be converted into DML. However, when opening it with Model Integrity, the error shown above is reported. But where can I modify this parameter? I have never used Allegro simulatio...
Syber PCB Design
Crazy Shell AI open source drone GPIO (LED flight status light, signal light control)
1. LED 1.1 Introduction to LED LED (Light Emitting Diode) is the abbreviation of light-emitting diode. LED is a very common lighting device in life. There are many types of LED in our lives, as shown in the figure below. ...
fengke Innovation Lab
Digi-Key Follow me Issue 2 + Task 1234 Submission
Thanks to Digi-Key and EE Forum for hosting this event. Content 1: Video Submission Video address: Task 1234 Submit Content 2: Task Submission Task 1: Control the screen to display Chinese The code is as follows: first impor...
王嘉翔 DigiKey Technology Zone
TI CCS & controlSUITE Troubleshooting Log
Problem 1. Opening controlSUITE does not display properly, only one File option is displayed Solution: After investigation, it was found that when controlSUITE was normal, it was not exited by clicking the X button, but by File- Exit. The above pr...
Aguilera DSP and ARM Processors
Successfully used ZYNQ to drive LTC2325-16
I have been working on ZYNQ (mining board) driving LTC2325-16 ADC these days . I feel that FPGA is too difficult. For a novice like me, it is not like a microcontroller that can "easily" use trial and error to complete the desired function by co...
littleshrimp FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Site Related: China chips Training TI Training Datasheet EEWORLD

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Search Index   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号