AD8591ART-REEL7 datasheet, PDF

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> AD8591ART-REEL7

AD8591ART-REEL7: Part NumberAD8591ART-REEL7; CategoryAnalog mixed-signal IC Amplifier circuit; File Size13105.46，17 Pages; ManufacturerRochester Electronics; Websitehttps://www.rocelec.com/

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

AD8591ART-REEL7 Overview

AD8591ART-REEL7 amplifier basic information:

AD8591ART-REEL7 is an OPERATIONAL AMPLIFIER. The commonly used packaging method is LSSOP,

AD8591ART-REEL7 amplifier core information:

The AD8591ART-REEL7 has a minimum operating temperature of -40 °C and a maximum operating temperature of 85 °C. Its peak reflow temperature is NOT APPLICABLE Its maximum average bias current is 0.00006 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the AD8591ART-REEL7 has a nominal slew rate of 3.5 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the AD8591ART-REEL7 gain becomes 0.707 times the low-frequency gain is 2200 kHz.

The AD8591ART-REEL7 has a nominal supply voltage of 2.7 V. The upper limit of its supply voltage is 6. The input offset voltage of VAD8591ART-REEL7 is 30000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of AD8591ART-REEL7:

The width of AD8591ART-REEL7 is: 1.65 mm and the length is 2.9 mm. AD8591ART-REEL7 has 6 terminals. Its terminal position type is: DUAL. Terminal pitch is 0.95 mm. Total pins: 6

AD8591ART-REEL7 amplifier additional information:

Its temperature grade is: INDUSTRIAL. And its humidity sensitivity level is: NOT SPECIFIED. AD8591ART-REEL7 is not Rohs certified. It contains lead. The corresponding JESD-30 code is: R-PDSO-G6.

The corresponding JESD-609 code is: e0. The packaging code of AD8591ART-REEL7 is: LSSOP. AD8591ART-REEL7 packaging materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. AD8591ART-REEL7 package pin forms are: SMALL OUTLINE, LOW PROFILE, SHRINK PITCH.

Its terminal forms are: GULL WING. The maximum seat height is 1.45 mm.

Recommended Resources

Use LED digital clock to make timing switch circuit

clamp amplifier circuit

Yale brand FB-12A heating and cooling fan circuit diagram

555 pyroelectric infrared greeting automatic identification and greeting circuit

Light controlled flash safety signal light circuit

Looking for C5505 eZdsp schematic: The webpage of this development board on TI official website has been invalid. I have been looking for it for a long time but couldn't find it. Recently, I am reading the principles, implementation and application of digital signal processing. This ...; 准音频算法工程师 DSP and ARM Processors

How can the pyboard measure frequency and duty cycle?: For example, if there is a signal of about 20k, how can I measure the frequency and duty cycle? The pyboard's Timer supports capture mode, but I haven't tried it, so I'm not sure how to use it. If it is a rectangular wave, is there an input...; spydf MicroPython Open Source section

The C6748 timer is in 32-bit mode: The timer initialization and interrupt service function codes in the associated mode are as follows: /********************************************************************************/ /* */ /* Timer/Counter Initialization*/ /* */ /************...; 火辣西米秀 DSP and ARM Processors

When BLE meets MEMS——BLE communication under MATLAB software: Previously, we introduced how to use Win10 system to program BLE host computer: When BLE meets MEMS - BLE program writing under Windows platform Here we introduce how to use MATLAB software to program a BLE host computer. MATLAB started t...; lb8820265 DIY/Open Source Hardware

How do I input an external clock signal into CC2530?: I plan to remove the original 32M crystal oscillator of CC2530 and use FPGA to generate a new 32M clock signal as the crystal oscillator. I want to use a coaxial cable to connect FPGA and CC2530. How can I input the external clock signal into CC2530...; 读书运动少上网 RF/Wirelessly

What type of transformer is this?: Hello power supply experts, what type of transformer is this? Power 280W Input 240V Output Dual 20V Please give me some scientific knowledge What type of transformer is this? The nameplate says: 50/60 Hz, which is obviously an indust...; kal9623287 Power technology

AD8591ART-REEL7 Also View