ADA4004-1ARZ datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> ADA4004-1ARZ

ADA4004-1ARZ: Part NumberADA4004-1ARZ; CategoryAnalog mixed-signal IC Amplifier circuit; File Size12484.12，17 Pages; ManufacturerRochester Electronics; Websitehttps://www.rocelec.com/; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
ADA4004-1ARZ-R7	Rochester Electronics LLC	ADA4004-1ARZ-R7 amplifier basic information:ADA4004-1ARZ-R7 is an OPERATIONAL AMPLIFIER. The commonl...
TLE2071IP	Texas Instruments	Low-Noise High-Speed JFET-Input Operational Amplifier 8-PDIP
TLE2071IPE4	Texas Instruments	Operational Amplifiers - Op Amps Low-Noise High-Speed JFET-Input

ADA4004-1ARZ Overview

ADA4004-1ARZ amplifier basic information:

ADA4004-1ARZ is an OPERATIONAL AMPLIFIER. The commonly used packaging method is SOP,

ADA4004-1ARZ amplifier core information:

The minimum operating temperature of the ADA4004-1ARZ is -40 °C and the maximum operating temperature is 125 °C. Its peak reflow temperature is 260°C and its maximum average bias current is 0.165 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the ADA4004-1ARZ has a nominal slew rate of 2.7 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the ADA4004-1ARZ gain becomes 0.707 times the low-frequency gain is 12000 kHz.

The nominal supply voltage of the ADA4004-1ARZ is 5 V, and its corresponding nominal negative supply voltage is -5 V. The input offset voltage of the ADA4004-1ARZ is 300 µV (Input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of ADA4004-1ARZ:

The width of ADA4004-1ARZ is: 3.9 mm and the length is 4.9 mm. ADA4004-1ARZ has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 8

ADA4004-1ARZ amplifier additional information:

Its temperature grade is: AUTOMOTIVE. And its humidity sensitivity level is: 1. ADA4004-1ARZ is not Rohs certified. It does not contain lead. The corresponding JESD-30 code is: R-PDSO-G8.

The corresponding JESD-609 code is: e3. The package code of ADA4004-1ARZ is: SOP. The materials used in the ADA4004-1ARZ package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The ADA4004-1ARZ package pin formats are: SMALL OUTLINE.

Its terminal forms are: GULL WING. The maximum seat height is 1.75 mm.

Recommended Resources

STK0105 power amplifier circuit diagram

Relaxation oscillator circuit composed of unidirectional thyristor

Temperature sensor used in crystal compensation circuit

Voice activated alarm circuit

Frequency multiplier composed of phase locked loop circuit

6OXT(1.0) computer motherboard circuit diagram_10

[2024 DigiKey Creative Competition] Progress Sharing--HA and MQTT Construction & ESP32-C6 Access to HA to Control RGB: Three boards were used in this event, namely the ESP32-C6 development board, the Raspberry Pi5 and the SiPEED 6+1 microphone array. They were briefly introduced in the previous unboxing post . Here are pictures of the boards: Here is th...; 夷则玖 DigiKey Technology Zone

Single Channel Sonar Receiver - Active Butterworth Filter: #ActiveButterworthFilter##ButterworthFilterCharacteristics The characteristic of Butterworth filter is that the frequency response curve in the passband is as flat as possible without fluctuations, and gradually decreases to zero in the stopband. On...; bqgup Innovation Lab

[MM32 eMiniBoard Review] + Green Plant Monitor: Initially, the plan was to use digital sensors to design a device with home environment detection and prompt functions, but the millisecond and microsecond delay functions it relies on were not available, making it difficult to achieve, so the...; jinglixixi Domestic Chip Exchange

Battery Pack SOC: Battery pack SOC For battery packs, the current fuel gauge implementation methods mainly include TI's impedance tracking, current integration coulomb counter, Kalman filtering, and estimated open circuit voltage method. Which one has known about BM...; QWE4562009 Discrete Device

How should ferrite beads be used and how should they be selected for gate drive circuits?: Noise is a constant problem for high-speed circuits. Whether it is noise on the power rail or the gate of the power FET, it can cause abnormal or even irreparable damage. Ferrite beads are one of the tools engineers have to deal with this noise. Thi...; qwqwqw2088 Power technology

【2024 DigiKey Creative Competition】Workplace Refreshing Magic Weapon Project-Work Submission: A magic weapon to boost your energy in the workplace Author: eew_cT3H5d 1. Introduction This work is a system for improving office environment and monitoring environment developed to solve the problem of office environment affecting off...; eew_cT3H5d DigiKey Technology Zone

ADA4004-1ARZ Also View