RBR56L42701TR datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> The resistor> RBR56L42701TR

RBR56L42701TR: Part NumberRBR56L42701TR; CategoryPassive components The resistor; File Size1491.31，2 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

RBR56L42701TR Overview

NJM741M-(TE1) amplifier basic information:

NJM741M-(TE1) is an OPERATIONAL AMPLIFIER. The commonly used packaging method is DMP-8

NJM741M-(TE1) amplifier core information:

The minimum operating temperature of NJM741M-(TE1) is -40 °C and the maximum operating temperature is 85 °C. Its peak reflow temperature is 260°C and its maximum average bias current is 0.5 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of NJM741M-(TE1) is 0.5 V/us. Its minimum voltage gain is 19952.6.

The nominal supply voltage of NJM741M-(TE1) is 15 V, and its corresponding nominal negative supply voltage is -15 V. The input offset voltage of NJM741M-(TE1) is 6000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Relevant dimensions of NJM741M-(TE1):

The width of NJM741M-(TE1) is: 5 mm, and the length is 5 mm. NJM741M-(TE1) has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 8

NJM741M-(TE1) amplifier other information:

Its temperature grade is: INDUSTRIAL. NJM741M-(TE1) does not comply with Rohs certification. It does not contain lead. The corresponding JESD-30 code is: S-PDSO-G8. The corresponding JESD-609 code is: e6.

The packaging code of NJM741M-(TE1) is: SOP. NJM741M-(TE1) packaging materials are mostly PLASTIC/EPOXY. The package shape is SQUARE. NJM741M-(TE1) package pin formats are: SMALL OUTLINE. Its terminal forms are: GULL WING.

The maximum seat height is 2 mm.

Recommended Resources

16-port 50GbE PHY transceiver, do you know it?

Lighting delay-off circuit using thyristors Part 3

Y-△ voltage reduction control circuit controlled by DC relay

Internal circuit of TDA1521

Zhengcun ZLDB motor protector typical application circuit

Common interface circuits for Hall effect integrated circuits

Comparison of Three Synchronous Designs in FPGA: For the convenience of everyone, I will directly post the content of the information sent by the OP in the reply without the OP's permission: In FPGA, signal synchronization is a common way to solve metastable problems. Common synchro...; 至芯科技FPGA大牛 FPGA/CPLD

Why does JTAG have 20 pins when it doesn't use many?: Why does JTAG have 20 pins when it doesn't use many? Anti-interference when converting cable transmission Thank you very much. What do you mean by conversion cable transmission? For JTAG, it is to replace the double-row cable with a sing...; 深圳小花 MCU

Selection of pull-up resistor value for common communication line: Hello everyone, I am a beginner. I am now learning to do a PCB board experiment. For the purpose of learning, I plan to use STM32 to connect multiple SPI devices at the same time. I have no problem connecting a single SPI device. Just follow the c...; 风轻轻 PCB Design

How Bluetooth 5 maximizes the range of Bluetooth low energy connections: Bluetooth no longer exists as a wireless protocol used only for personal area networks (PANs). Three new data rates have been added to the specification, two of which are specifically tailored to increase the range of Bluetooth low energy connecti...; Jacktang Wireless Connectivity

High Accuracy Split-Phase CT Fuel Gauge Reference Design Using Independent ADCs: The reference design implements Class 0.1 split-phase energy metering using high-performance, multi-channel analog-to-digital converters (ADCs). Independent ADCs sample the output of current transformers (CTs) at 8kHz to measure the current an...; qwqwqw2088 Analogue and Mixed Signal

Problems with STM32 and passive buzzer playing sound: The pin drives the passive buzzer via PWM to produce different sounds Looking at the examples on the Internet, the beat frequency and other parameters corresponding to the sound file are placed in an array and then called one by one to play the de...; 程序会不会 stm32/stm8

RBR56L42701TR Also View