EEWORLDEEWORLDEEWORLD

Part Number

Search
 

MA-333-CP

Part NumberMA-333-CP
CategoryAmplifier circuit   
File Size2270.5,8 Pages
ManufacturerAnalog Systems (SH) Co., Ltd.
Download Datasheet Parametric

Alternative parts

Part Number Manufacturer Description
SE530FE Ideal Semiconductor Inc Basic information about SE530FE amplifier:SE530FE is an OPERATIONAL AMPLIFIER.SE530FE amplifier core...
MA-333-CH Analog Systems (SH) Co Ltd Basic information of MA-333-CH amplifier:MA-333-CH is an OPERATIONAL AMPLIFIER. The commonly used pa...
TL071BIN STMicroelectronics Low noise JFET single operational amplifier
TL071BCN STMicroelectronics Low noise JFET single operational amplifier
MC35001AN STMicroelectronics GENERAL PURPOSE SINGLE JEFT OPERATIONAL AMPLIFIERS
TL081BCJG Texas Instruments OP-AMP, 5000uV OFFSET-MAX, 3MHz BAND WIDTH, CDIP8, 0.300 INCH, HERMETIC SEALED, CERAMIC, DIP-8

MA-333-CP Overview

Basic information of MA-333-CP amplifier:

MA-333-CP is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are PLASTIC, DIP-8

MA-333-CP amplifier core information:

The minimum operating temperature of MA-333-CP is and the maximum operating temperature is 70 °C. Its peak reflow temperature is NOT SPECIFIED. Its maximum bias current at 25°C is: 0.0001 µA. Its maximum average bias current is 0.0001 µA and its maximum input offset current (IIO) is only 0.0014 µA.

How to simply check the efficiency of an amplifier? Looking at its slew rate, the MA-333-CP has a nominal slew rate of 15 V/us. The manufacturer specifies a maximum slew rate for the MA-333-CP of 2.5 mA and a minimum slew rate of 10 V/us. Its minimum voltage gain is 32000. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the MA-333-CP gain becomes 0.707 times the low-frequency gain is 4000 kHz.

The nominal supply voltage of the MA-333-CP is 15 V, and its corresponding nominal negative supply voltage is -15 V. The power supply range is: +-15 V. The input offset voltage of the MA-333-CP is 5000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of MA-333-CP:

MA-333-CP has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm. Total pins: 8

MA-333-CP amplifier additional information:

MA-333-CP adopts the VOLTAGE-FEEDBACK architecture. It belongs to the low-bias class of amplifiers. It does not belong to the low offset class of amplifiers. The frequency compensation status of MA-333-CP is: YES. Its temperature grade is: COMMERCIAL.

MA-333-CP is not Rohs certified. It contains lead. The corresponding JESD-30 code is: R-PDIP-T8. The corresponding JESD-609 code is: e0. The encapsulation code of MA-333-CP is: DIP.

MA-333-CP packaging materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. MA-333-CP package pin format is: IN-LINE. Its terminal form is: THROUGH-HOLE.

Share a book on deep learning: Deep learning with Python
Share a book on deep learning, Deep learning with Python, very classic, good information on deep learning I thought they were different books, but they turned out to be the same... Anyway, thanks a lot. ...
grarrow Integrated technical exchanges
cs+ cannot simulate debugging
I used ap4 to generate code, and then created a new project with cs+ for ca. After adding the c file, I set the device configuration in Link Options according to the content in the r_option_ca.txt file, but I could not enter the simulation. I used R...
wdliming Renesas Electronics MCUs
[Automatic clock-in walking timer system based on face recognition] Unboxing (1): SiPEED Maix Bit (K210)
Today, the development board of Digi-Key's Innovation Design Competition has finally arrived. I am full of excitement and anticipation! Here is an unboxing report and a hands-on experience! (I'll tell you in advance, it's pretty nice! ) 1. Unbo...
alanlan86 DigiKey Technology Zone
DSP C6000 assembly, handling of data byte non-alignment issues
Basic knowledge: Use LDB to read 1 Byte, LDH to read 2 Bytes, LDW to read 4 Bytes, and LDDW to read 8 Bytes. Register 32 of C6000 is bit, so when using LDDW, you need to use a register pair (such as A5:A4). When processing data, whether the bytes ...
fish001 DSP and ARM Processors
The concepts and differences between FPGA and CPLD
1. Basic concepts of FPGA and CPLD 1. CPLD CPLD is mainly composed of a programmable interconnect matrix unit around a programmable logic macro cell (LMC). The LMC logic structure is relatively complex and has a complex I/O unit interconnection struc...
信盈达纪老师 TI Technology Forum
Reliability Design of Electrically Driven Titanium Wire (SMA) (6) Temperature Control
【Foreword】 Shape memory alloy (SMA), also known as morphological memory alloy and titanium-nickel memory alloy, is composed of Ti (titanium)-Ni (nickel) materials. It is a wire made through multiple processes, which we call titanium wire for short...
272151979 Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Site Related: China chips Training TI Training Datasheet EEWORLD

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Search Index   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号