543 views|6 replies

287

Posts

0

Resources
The OP
 

What is the function of the diode in the circuit diagram? [Copy link]

This post was last edited by Knight97538 on 2024-7-4 10:04

Please advise, there is a diode D1 in the AC charging control pilot circuit diagram, so what is the function of this diode?

This post is from Power technology

Latest reply

One-way signal, prohibiting current backflow at the control end.   Details Published on 2024-7-4 15:47
 
 

4771

Posts

12

Resources
2
 
Personal understanding, to prevent backflow.
This post is from Power technology
 
 
 

2944

Posts

0

Resources
3
 

The role of isolation.

This post is from Power technology
 
 
 

1144

Posts

2

Resources
4
 
It can play the role of detecting signal isolation. In fact, when the detection point 2 detects the on-board charger and the device controller at the same time and is connected, the on-board charger will not affect the device controller.
This post is from Power technology
 
 
 

140

Posts

0

Resources
5
 

One-way signal, prohibiting voltage reflux at the control end!

This post is from Power technology
Personal signature发上等愿,结中等缘,享下等福。择高处立,就平处坐,向宽处行。
 
 
 

277

Posts

0

Resources
6
 

One-way control to prevent signal feedback and cause erroneous operation

This post is from Power technology
 
 
 

307

Posts

0

Resources
7
 

One-way signal, prohibiting current backflow at the control end.

This post is from Power technology
 
 
 

Find a datasheet?

EEWorld Datasheet Technical Support

Featured Posts
Analog Circuit Basics Tutorial! E-book

Recommended ★★★★★ Data Type E-books Document language Simplified Chinese

Wireless LAN and Network Security Technology

Comprehensive Analysis of Wireless LAN and Network Security Technology

Contradictions and tradeoffs in switching power supply design

Overview Designing a switching power supply is a process full of contradictions. You can't have your cake and eat it ...

Lora parameter calculation and RF transmission distance calculation formula and tools

This post was last edited by xulikai on 2019-10-20 10:36 This content is originally created by EEWORLD forum user xuli ...

How to deal with the prompt "Transient time point calculation did not converge" during Multisim simulation

How to deal with the error "Transient time point calculation did not converge" when simulating with Multisim under high- ...

6. DMA implementation of USART1 sending and receiving

The following GD32L233C-START special review: 1. Unboxing review https://bbs.eeworld.com.cn/thread-1192788-1-1.html 2. G ...

How to configure ST-LINK/V2 in the STM32CUBEIDE environment?

There is always an error in configuring ST-LINK/V2 in the STM32CUBEIDE environment. Which master knows how to configure ...

全志V853 NPU 转换部署 YOLO V5 模型

# NPU conversion and deployment of YOLO V5 model This article takes the YOLO v5s model as an example to detail the conve ...

[DigiKey "Smart Manufacturing, Non-stop Happiness" Creative Competition] - Current Conversion Circuit Simulation

This post was last edited by lansebuluo on 2023-11-25 16:41 This chapter is used to explain the circuit for converting ...

"Machine Learning Algorithms and Implementations - Python Programming and Application Examples" Deep Learning AlexNet

The network architecture of AlexNet is shown in the figure below: 831557 It can be seen that the Alexnet model consist ...

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号
快速回复 返回顶部 Return list